Search:

There could be several problems.

New Firmware configuration.
Print speed to fast causing hot end to cool.
Bad hot end heater.
Loose hot end wires.
Power wires running to the controller will...

Was going the suggest just that, though you are correct.
Have a Pair of the Any cubic Kobra 3 Combo 's
Purchased a full set of nozzles 0.2mm 0.4mm 0.6mm and 0.8 mm a set for each Kobra its only...

Do not know how good the information is though you can search again using the description on the link.

I visited the HzdaDeve store and could not find these nozzles.

I found this link

20116

Partly because I own a pair of these color printers, an partly because we could use more technically minded individuals.

I would suggest looking at the New Anycubic Kobrea 3 Combo
This model has...

Hi

I have been looking for a users manual for Orca Slicer 2.3.0 or anything even close as to allow me to use the full potential of slicers.
Would be happy to see this in any form pdf, you-tube...

Here we have a Painted object shown in the photo below.

If the Painted is in Object mode then they will have a place to select/change the filament.

Painted Object

Else if they do not have,...

Yesterday I found the newest Orca Slicer 2.3.0 RC Build 79a5a9b build and printed using a USB Flash drive.

This means maybe the Anycubic Kobra 3 users have 2nd chose of slicer that will print...

I too have been using Firefox for a super long time can not remember how long.

Guess could look back is my archives to see how long I have been using Firefox.
I know it was around not to long...

ok Examples
This is what I see using Firefox browser.

20077

And this is what I see using the Edge and Chrome browser

20078

Can someone on this forum help me.

I like FireFox browser though I find that on this forum I can not see the Advanced forum editing features.

Is there any thing I can do about this other than...

Post the location of the STL. Please

What you are requesting is simple.
Thinker Cad has many you tube videos on how to do this

Go to Thinker Cad and upload the model you have.
Cut the center you do not want and add a straight piece...

Anycubic Slicer Next 1.3.3 For Windows

What's new:
1. Added "Skip Part" feature (Currently for S1, version ?2.8.4.3)
2. Improved login region prompts.
3. Fixed temperature errors when leveling...

Anycubic Slicer Next 1.3.3 For Windows

What's new:
1. Added "Skip Part" feature (Currently for S1, version ?2.8.4.3)
2. Improved login region prompts.
3. Fixed temperature errors when leveling...

Try reading this article.

https://www.reddit.com/r/FlashForge/comments/12sdkb6/if_your_flash_forge_creator_pro_thermocouple/

I have purchased two of these https://store.anycubic.com/products/kobra-3-combo

You may what to have a look they print pretty well.
...

Should have included a case photo also here is one.
My hinges are on top and lifted up no heater just a vent fan on low speed.
Two thermometers one behind each printer single open space for both...

I operated my enclosure at 80-100F this is not above the 3D Printers standard operation temperature.
The main goal for the enclosure is to stop the cool breezes from blowing across the models while...

I Have three Hictops 3D Printers they are similar to the ENDER 3 V2
One 12 volt printer and two 24 volt printers.

This is my V-Ref values for 9 year on these 3D Printers.

12 volt power supply...

PLA+ requires a little hotter nozzle and a little faster print speed, reduce retraction to about 1mm, enable Z-hop to about 0.4mm

ELEGOO NEPTUNE 4 PRO: How to adjust the eccentric wheel?


https://www.youtube.com/watch?v=PdIiIy7f1Jk


Hope this helps

Hi airscapes

I had three older 3D Printers but none of them can 3D Print aluminum.
I still have 2 Older Hictop 3D Printers and 2 Newer Anycubic Kobra 3 combo color printers. and they cannot 3D...

There are many things that could cause this problem.

1. Nozzle could be damaged
2. Smooth Rods and Rod bearings could be dirty or insufficiently lubricated.
Great Bearing Cleaning video...

Ok so you are wanting a 3D Printer.
First printer you stated maybe a Anycubic Kobra 3 currently have two myself and two Hictops 3DP12.
I find Kobra 3 a working Color 3D Printer though the waste can...