Close



Dig deeper, search our News website




Search:

Type: Posts; User: Gambo

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Could the filament be jamming when the bowden...

    Could the filament be jamming when the bowden tube is bent at one extreme of the x travel of the extruder head ?
  2. I looked up what PEX is and unless there is...

    I looked up what PEX is and unless there is another Polymer than the one listed in Wikipedia this stuff is just cross linked poly ethylene so it's good difficult to see what would stick to it...
  3. Amen to that !

    Amen to that !
  4. There is an old saying " If sounds too good to be...

    There is an old saying " If sounds too good to be true, it probably is too good to be true."

    The in general the trouble with information on the internet is anyone can post their opinion as fact...
  5. Hi Your problem sounds like there is a mechanical...

    Hi Your problem sounds like there is a mechanical miss alignment but You do not say what printer you have so it is very difficult to help.
  6. it stands to reason if the prints stuck on the...

    it stands to reason if the prints stuck on the original bed put not on the "improved" thr likely cause is the bed so try reverting to the original !!

    On the subject of print beds I have no...
  7. Replies
    10
    Views
    2,107

    Don't forget all brands of a material are not...

    Don't forget all brands of a material are not equal some brands are much more difficult than others - personally my main materials are ABS and nylon and some brands of each I have been able to...
  8. Replies
    9
    Views
    1,022

    I made both of mine out of Acrylic sheet but...

    I made both of mine out of Acrylic sheet but Acrylic sheet is quiet expensive so plywood would do with an Acrylic door. Both of my enclosures have ope tops
  9. Replies
    9
    Views
    1,022

    ABS is not one material but a whole range of...

    ABS is not one material but a whole range of different materials some easier than others and some that seem not to be printable at all. There are a number of ABS FILAMENTS using a low warp...
  10. @SKel. The Creality CR30 print mill does just...

    @SKel. The Creality CR30 print mill does just that printing on a sort of conveyor belt.
  11. Replies
    2
    Views
    651

    You don't say which material you are using but I...

    You don't say which material you are using but I assume it's PLA. One thought that comes to mind is have you inadvertently set the filament size to ,2.85 in the slicer profile when you changed...
  12. Choosing the right filament brand to print is...

    Choosing the right filament brand to print is indeed the key to Nylon Printing -About a year ago I needed to print some parts for a project underway in my company and since they were spray nozzles...
  13. Thread: Best ABS Printer

    by Gambo
    Replies
    7
    Views
    2,031

    Fred- dot-u oh how I agree!

    Fred- dot-u oh how I agree!
  14. Hi how are you connecting to the printer are you...

    Hi how are you connecting to the printer are you using Prontface
  15. Replies
    19
    Views
    2,491

    Hi Scuff Levwl. I sand the surface of the...

    Hi
    Scuff Levwl. I sand the surface of the Tufnol/Garolite with a 240 grit abrasive pad until the surface is matt all over with no trace of shine, this only takes a couple of mins.

    The PVA I use...
  16. Replies
    19
    Views
    2,491

    240 Grit foam back 3ms

    240 Grit foam back 3ms
  17. Replies
    19
    Views
    2,491

    Yes the Garolite you give with the link to is ok...

    Yes the Garolite you give with the link to is ok but a dear grade talk to McMaster-Carr their CE grade will do.I just cut mine to size with a craft knife. I use 1mm thick but in us seem to have 1/32...
  18. In any case don't abandon the Sapphire Plus for a...

    In any case don't abandon the Sapphire Plus for a Sapphire plus it's almost the same machine and if the one I have just as bad to get going. Mine now works almost ! It gives very good prints with...
  19. Replies
    19
    Views
    2,491

    Tufnol and Garolite are the same thing SRBF for...

    Tufnol and Garolite are the same thing SRBF for synthetic resin bonded fabric from McMaster- Carr.

    The grade used by Taulman is Garolite LE grade but a cheaper grade will do cheap sheets are...
  20. Replies
    19
    Views
    2,491

    Hey did someone call!fYes I have been using...

    Hey did someone call!fYes I have been using Garolite (known as Tufnol in UK) almost exclusivly for more than a year with all sorts of filaments. On my ender 3 I have a glass sheet on the heated...
  21. yes you'r right I'd forgotten about the dual Z...

    yes you'r right I'd forgotten about the dual Z drive motors still I hate solving problems you don't have!
  22. If you want to save yourself a world of hurt...

    If you want to save yourself a world of hurt forget the auto levelling and buy a sheet of borosilicate glass I have been using that for a year on the Ender 3 and ever since I got the Sapphire Pro....
  23. The Process used professionally is:- First clean...

    The Process used professionally is:-
    First clean off any sticky coating on the surface with Iso Propanol IPA,
    Harden the surface by exposing to UV light from a light box.

    When this is done you...
  24. Yes I think so

    Yes I think so
  25. you've got me all wrong i was not thinking of...

    you've got me all wrong i was not thinking of pizza just the red wine that goes with it !!!
Results 1 to 25 of 217
Page 1 of 9 1 2 3 4