Close



Dig deeper, search our News website




Search:

Type: Posts; User: adamfilip

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    5,013

    Practical home use of 3D printing?

    I have had a 3d printer for 2 years. started with a makerfarm i3v kit and then later custom made myself a corexy openbuilds machine.
    I enjoy tinkering/building but once the printer was tweaked and...
  2. Replies
    40
    Views
    24,887

    PETG is awesome. very strong. No Smell. Minimal...

    PETG is awesome. very strong. No Smell. Minimal warp (enslosure preferred), sticks well to PEI, Food Safe, No toxic air particles like ABS, Issues with it are excessive oozing, and its hard to clean,...
  3. Replies
    40
    Views
    24,887

    I use a PEI Surface and print almost exclusively...

    I use a PEI Surface and print almost exclusively PETg
  4. Replies
    14
    Views
    15,229

    Also checkout the DuetWifi very comparible to the...

    Also checkout the DuetWifi very comparible to the Smoothieboard/Ware
  5. Replies
    13
    Views
    13,054

    Bed Temp not accurate

    Im running into a issue where i set my bed temp to 80 and the display says 80. but when i measure the bed temp with two different thermometers/readers it says around 55, i have to compensate by...
  6. Replies
    1
    Views
    3,932

    PETG Print Quality Help

    Trying to improve print quality with my Custom COREXY machine
    Running PETG at 255 degrees, with 70 degree PEI Bed
    I have also run at 235 degrees with similar print quality

    Extruder is a Bondtech...
  7. Replies
    18
    Views
    13,147

    sure, but this isnt corexy related really.. I am...

    sure, but this isnt corexy related really.. I am planning on making a version of this hinged gantry for my Makerfarm i3v 12
  8. Replies
    18
    Views
    13,147

    Just updated to Marlin UBL v2 redid the probe...

    Just updated to Marlin UBL v2 redid the probe test

    nice results! from M48 V4 P10

    READ: Mean: -0.997358
    READ: Standard Deviation: 0.000677

    :)
  9. Replies
    18
    Views
    13,147

    Are you referring to the Mean or Standard...

    Are you referring to the Mean or Standard Deviation?
  10. Replies
    18
    Views
    13,147

    so whats considered a good result?

    so whats considered a good result?
  11. Replies
    18
    Views
    13,147

    Here are the results of the M48 V4 P10 READ:...

    Here are the results of the M48 V4 P10

    READ: Mean: 0.664402
    READ: Standard Deviation: 0.002912
  12. Replies
    18
    Views
    13,147

    Havent had a chance to really print with it yet....

    Havent had a chance to really print with it yet. been testing and tweaking so many things related to the printer..
    but I will very soon i hope
  13. Replies
    19
    Views
    21,771

    I dont have a good example to show. the printer...

    I dont have a good example to show. the printer prints fine. just not great.. maybe my expectations are too high
  14. Replies
    18
    Views
    13,147

    Yep, that printer inspired me to make this...

    Yep, that printer inspired me to make this version.
  15. Replies
    3
    Views
    6,858

    stick with 1.75.. ive been on 2.85 for a while...

    stick with 1.75.. ive been on 2.85 for a while and it oozes more then 1.75
  16. looks like it would really slow down the...

    looks like it would really slow down the printing. switching, purging,
  17. Replies
    2
    Views
    4,089

    There is no option to change output voltage. just...

    There is no option to change output voltage. just 12v output
    it is a cheap SSR
  18. Replies
    18
    Views
    13,147

    Well my bed is completely solid. and my Gantry...

    Well my bed is completely solid. and my Gantry cant go down that far. it hits a physical limit.
    if it tried to drive down.. the spring would take up the pressure.

    I will try the M48 V4 P10 when I...
  19. Replies
    18
    Views
    13,147

    Here is it working. https://youtu.be/Iq-L2mW2IyM

    Here is it working.
    https://youtu.be/Iq-L2mW2IyM
  20. Replies
    2
    Views
    4,089

    Silicone Heater, not getting hot enoough

    I have a 300x300 silicone heater connected via SSR to my Rumba
    running on 12v 30A power supply

    when i turn on the heat it maxes out at around 52 degrees..
    the heater has two Red Power cables.....
  21. Replies
    18
    Views
    13,147

    Haven't had time to test it. But it only needs to...

    Haven't had time to test it. But it only needs to lift a tiny amount to trigger the switch. And yes spring is to set tension
  22. Replies
    18
    Views
    13,147

    Hinged Ganry with ABL probe

    Working on a new CoreXY printer
    and was hoping you guys could give me your two cents on the basic idea of how ABL is handled in this gantry design

    A Special gantry for openbuilds vslot using Mini...
  23. Replies
    19
    Views
    21,771

    I ended up upgrading the Z screws to fine Acme...

    I ended up upgrading the Z screws to fine Acme screws and run geared nema 17s
    the machine sits on a some ceramic plates to keep everything flat and level.
    i upgraded he bed to a aluminum plus boro...
  24. Replies
    19
    Views
    21,771

    Why does my printer suck.

    Ok well I have been tweaking and upgrading my Makerfarm i3v 12" for almost 2 years..
    ive become very familiar with calibrating and testing.

    done lots of little things to improve the performance...
  25. Replies
    18
    Views
    14,732

    Switch to PetG its like ABS except it doesnt...

    Switch to PetG
    its like ABS
    except it doesnt Smell, warps way less and its stronger. oh and considered food safe. (not harmful particles) so ive heard.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4