Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 37 minute(s) ago.

  1. Does not matter. Thank You.

    Does not matter.

    Thank You.
  2. Replies
    8
    Views
    241

    Then I proposse another way to get your 3D...

    Then I proposse another way to get your 3D Printer working.

    Great Bearing Cleaning video
    https://www.youtube.com/watch?v=KQHugGSQd5M
  3. Please post the you-tube video would like to see...

    Please post the you-tube video would like to see this one.
  4. Replies
    2
    Views
    885

    Wanted to make a foot Note Here. When I...

    Wanted to make a foot Note Here.

    When I upgraded to Marlin 2 some time Ago had to forgo the use of M503 as not using it saved me enough memory to enable me to use the Marlin 2 versions.
  5. Replies
    2
    Views
    120

    WOW this is close but with precise placement of...

    WOW this is close but with precise placement of the model on the build and mechanical end-stops placement this can be achieved.
    Though this is going to take a skilled 3D Printer operator to...
  6. Most of us went thru the exact same experience,...

    Most of us went thru the exact same experience, we were not blessed with a perfect print every time.
    We had to learn that the first layer height is in a small range that is hard to achieve....
  7. It looks like the temperature for the first few...

    It looks like the temperature for the first few layers is too hot then once the correct temperature is acquired then printing is fine.
    Can you verify the what to hot-end temp is for those layers.
  8. Replies
    8
    Views
    241

    Measure the distance between the smooth rods at 3...

    Measure the distance between the smooth rods at 3 locations MIN, Center and MAX on the X-Axis to See where they are not parallel.
    Larger or Smaller gap between the smooth rods.
  9. Replies
    8
    Views
    241

    Say you have a pair of smooth rods they are in...

    Say you have a pair of smooth rods they are in parallel, what would happen if the smooth rods got too close to each other,
    They would bind and the same would happen if the smooth rods got to far...
  10. Replies
    8
    Views
    241

    As you have stated the X-Axis seems a bit stiff...

    As you have stated the X-Axis seems a bit stiff when moved to far left this can be caused by binding.
    This could mean that to smooth rod holder are out of alignment. Remove the binding nd you solve...
  11. Replies
    18
    Views
    1,040

    This truly was a fun project. finally killed...

    This truly was a fun project.

    finally killed my Heat Brake {Throat} and Nozzle after two years of use.
    15583
  12. I have never had a PLA model Warp, my Hot-bed is...

    I have never had a PLA model Warp, my Hot-bed is between 46-60C. In face I have not had an ABS Model Warp since building an enclosure for my 3D Printers.
  13. Replies
    10
    Views
    743

    In all Gambling there is cheating on both sides....

    In all Gambling there is cheating on both sides.

    https://www.thefashionball.com/trends/woman-cant-believe-casino-took-8-5-million-jackpot-away/
    https://www.youtube.com/watch?v=qAJMQVCaznM...
  14. Replies
    18
    Views
    1,040

    I have the printer setup using Marlin system...

    I have the printer setup using Marlin system Defaults which are a bit fast.
    To explain as sometime you load the file the estimated time is lower or higher.

    You are most likely the same place that...
  15. Replies
    18
    Views
    3,838

    I understand have been using Cura 15.04.6 forever...

    I understand have been using Cura 15.04.6 forever because it was so easy to use, though finding that it has a lot to be desired.

    Prusaslicer 2.3.0 alpha 4 still has a few bugs though with users...
  16. WOW That was crazy, somehow I got into Edit mode...

    WOW That was crazy, somehow I got into Edit mode on your post!!!

    Well the power supply you have has another fuse it is a thermal fuse.
    On the cover label of the power it states "Warning do not...
  17. Replies
    18
    Views
    3,838

    Read about Prusaslicer advanced features this is...

    Read about Prusaslicer advanced features this is free an has impressed me.

    https://help.prusa3d.com/en/article/modifiers_1767/
  18. Replies
    3
    Views
    351

    Noted your Vref current settings. This is Mine...

    Noted your Vref current settings.
    This is Mine for both 12 v and 24 volt 3D Printer Systems.

    Hictop Axis
    Stock
    12volt
    24volt


    X-Axis
  19. Replies
    18
    Views
    1,040

    This has happened from the start, having to...

    This has happened from the start, having to decide whether to print the surface layers first or second, how many Perimeters are needed.
    Then my computer crashed my configurations needed restored...
  20. Replies
    18
    Views
    1,040

    Final Print. 15552 15553 Print Time 2...

    Final Print.

    15552

    15553

    Print Time 2 hours 4 minutes

    To give this a better overall look it will require another top layer, this will add 7 minutes to print time.
  21. Replies
    3
    Views
    351

    We can help you, if you can have Patience. This...

    We can help you, if you can have Patience. This could be short or a long process.

    Lets start with more information than you have given us.
    Post a picture of your 3D Printer, post your Marlin...
  22. Replies
    18
    Views
    1,040

    They say the camera takes off lbs well the camera...

    They say the camera takes off lbs well the camera took off the rough rough edges.
    Though being somewhat of a perfectionist it did have a lot to be desired.. .

    I printed it at Scale 100%

    15547...
  23. Start with giving us more information. Post your...

    Start with giving us more information.
    Post your Cura slicer settings.

    In fact If you have an Ender 3 you should be using Prusaslicer also and you could attach a .3mf project file for us to look...
  24. Replies
    2
    Views
    472

    I have noted that Marlin 1.1.9 had problems and...

    I have noted that Marlin 1.1.9 had problems and you should use Marlin 1.1.9BF

    OR

    You could choose to upgrade to Marlin 2 as I am using Marlin 2.0.6 on My Prusa Compatible 3D Printer with...
  25. After printing the Calibration cubes, I do not...

    After printing the Calibration cubes, I do not know where these G-Code came from though they printed in excellent condition.

    If you sliced them with Pruseslicer post your 3MF file will look at...
Results 1 to 25 of 490
Page 1 of 20 1 2 3 4