Close



Dig deeper, search our News website




Search:

Type: Posts; User: Bruce19

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    5,748

    Sorry dont need any furnature cleaning but...

    Sorry dont need any furnature cleaning but thank you
  2. Replies
    1
    Views
    826

    ENDER 3 Pro stock Glass bed

    ENDER 3 Pro stock Glass bed
  3. Replies
    1
    Views
    826

    Can any tell me whats going on

    I tried to print a geodesic planter with PTEG about 5 times, each failed. I had sucessfully printed with that freash out of the package a different item. When I kept failing I printing PLA. This...
  4. Replies
    2
    Views
    1,314

    look on youTube CHEP and Teaching Tech. They can...

    look on youTube CHEP and Teaching Tech. They can walk you thru swaping out board on you ender 5 Im getting ready to swap out my 8 bit for SKR 1.4 Pro in my Ender 3 pro
  5. Replies
    13
    Views
    5,748

    I have found the BEST thing to clean the bed of...

    I have found the BEST thing to clean the bed of exces stick glue, is with Windex and a razor blade. lil messy. spray windex on and see it turn purple, scrape into pile and wipe off with paper...
  6. I just ordered the SKR 1.4 turbo board, came with...

    I just ordered the SKR 1.4 turbo board, came with WIFI board, WRITER, and DCDC. ALSO Ordered 5 TMC2226 stepper drivers
  7. Anyone have the new TMC 2226 on a SKR 1.4 turbo

    hello I have a ENDER 3PRO soon to be upsized. I want to replace mainboard with 32bit board. Im looking at the 1.4 Turbo. I was gonna get the 2209 drivers but now see TMC 2226 drivers. Id like to get...
  8. Replies
    2
    Views
    616

    AUTOWIZ YES I just found out about the TMC2226...

    AUTOWIZ YES I just found out about the TMC2226 stepper drivers right after posting the above question. I had written to BIQU with questions including the 2226THANK YOU
  9. Replies
    2
    Views
    616

    TMC 2209 stepper drivers question

    I have a Ender 3 pro and am looking at the BIQU SKR 1.4 turbo board. I see where I can purchase that board with 2209 v1.2 stepper drivers. I recently saw online 2209 v3.0 stepper motor drivers sold...
  10. Replies
    2
    Views
    1,367

    What Causes This?

    Question. Do nozzles "Wear out"? I do have brand new nozzles to install but wonder why this happens. Bed leveling is spot on
  11. Replies
    0
    Views
    510

    What causes this?

    hello Having just reassembled my hot end from a missdirected filament travel and resulting diagnose. I leveled bed with paper method. Thinking I had bed level I applied my stick glue. What I got in...
  12. I first tried to remove tube heat break? from...

    I first tried to remove tube heat break? from heat block. At first it wouldn't budge. Then I heated it up to 195 and out it came. Tomorrow I'll clean the threads because on heat break threads, they...
  13. DONT know if Imentioned I have a Ender 3 Pro

    DONT know if Imentioned I have a Ender 3 Pro
  14. Just read your reply The "heat break" may be...

    Just read your reply The "heat break" may be threaded going into heat block, but held inside the cooling fin with a set screw only, as seen in the picture with blue circle, there are no threads at...
  15. Heat break? Is that the pipe/tube shown attaced...

    Heat break? Is that the pipe/tube shown attaced to heat block? Is that removable? How attached, threads, pressure fit? So that tube/pipe should extend into heater block so as when nozzle is...
  16. Replies
    13
    Views
    5,748

    I neglected to mention. AFTER 3-4 prints I spray...

    I neglected to mention. AFTER 3-4 prints I spray widex on the bed and scrape with a razer blade to remove old glue. I repeat until no more purple glue is seen, then I wipe down with acetone and...
  17. filament filament all over where shouldnt be, how do I fix this

    I just finished a 27 hour print. And I have to say it was the "dirtiest" print I've ever had. There was filament pieces all over the bed. During the print, it looked like filament was "leaking" from...
  18. Replies
    17
    Views
    6,648

    I deleted ALL pervious versions of Cura i had in...

    I deleted ALL pervious versions of Cura i had in this pc. i only have version 4.6.1 now and look whats new
  19. Replies
    17
    Views
    6,648

    It could be one line of code to communicate with...

    It could be one line of code to communicate with your printer is not optimally written. And yes, I guess like antivirous programs, have to have other AV programs erased b4 new AV installed. Do you...
  20. Replies
    14
    Views
    3,743

    Thank You When the print is ending, before I...

    Thank You When the print is ending, before I print the next print Ill look into that Z setting
  21. Replies
    17
    Views
    6,648

    So maybe I have to erase Cura 4.1, 4.1.1 , 4.5...

    So maybe I have to erase Cura 4.1, 4.1.1 , 4.5 and get Cura 4.6 one version
  22. Replies
    9
    Views
    4,042

    HMMMM :-) Maybe that upgradeb is down the road...

    HMMMM :-) Maybe that upgradeb is down the road if I understand corectlly Thank You
  23. Replies
    14
    Views
    3,743

    How in say Cura 4.4.1 OR 4.5 do I adjust Z first...

    How in say Cura 4.4.1 OR 4.5 do I adjust Z first layer setting?
  24. Replies
    14
    Views
    3,743

    I use a now a boro glass plate, lil purple elmers...

    I use a now a boro glass plate, lil purple elmers stick glue and it sticks great. sometimes too great. I want to try dimafix or magicgoo(not sure name) but just bought 6 tubes elmers
  25. Replies
    9
    Views
    4,042

    REEFSIDER SHOOT thats what I was affraid of....

    REEFSIDER SHOOT thats what I was affraid of. Question: what are benifits running 3mm filament should I decide at some point......
Results 1 to 25 of 65
Page 1 of 3 1 2 3