Close



Dig deeper, search our News website




Search:

Type: Posts; User: Horia

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: Under exrusion

    by Horia
    Replies
    17
    Views
    11,384

    Thank you for the interest, we compromised to...

    Thank you for the interest, we compromised to resolve the problem, but it's not the best solution. I presume it's mechanical because we tested a lot. We will make that model again, and will post the...
  2. Thread: Under exrusion

    by Horia
    Replies
    17
    Views
    11,384

    I mentioned in the first post that it's a Flash...

    I mentioned in the first post that it's a Flash Forge Creator Pro, 2015 model. It has printed almost 1000 meters and I guess that it needs some service.
    I didn't write a lot of information because...
  3. Thread: Under exrusion

    by Horia
    Replies
    17
    Views
    11,384

    The cause is almost sure mechanical. We will...

    The cause is almost sure mechanical. We will probably need to change some parts in the near future. We made a detour and set the layer start points at random points to minimize the effect. In the...
  4. Thread: Under exrusion

    by Horia
    Replies
    17
    Views
    11,384

    No, it's not the slicer. The problem is that...

    No, it's not the slicer. The problem is that after travel moves there is no extrusion for a few moments. Not all the prints have this problem, but when I print multiple objects on the same plate this...
  5. Thread: Under exrusion

    by Horia
    Replies
    17
    Views
    11,384

    It is happening with every filament and almost...

    It is happening with every filament and almost every print.
  6. Thread: Under exrusion

    by Horia
    Replies
    17
    Views
    11,384

    Under exrusion

    Hello, we have some problems with our FFCP.
    It seems like there is no consistent extrusion at the layer start or after travel moves.

    Here are some pictures:...
  7. Replies
    11
    Views
    9,738

    Thanks! :o I have another thread in the blender...

    Thanks! :o
    I have another thread in the blender artists forum and am hopefull that someone will light the way for this procedure in Blender. When I saw a pro using this FREE software I instantly...
  8. Replies
    11
    Views
    9,738

    All our printers have 0.4 nozzle so, 0.35 would...

    All our printers have 0.4 nozzle so, 0.35 would be the maximum of vertical declivity that we feel safe with :)
  9. Replies
    11
    Views
    9,738

    So, here...

    So, here is my wip apple in 123d Design. I guess it will do the job after all. Preety neat features, forgot all about transforming sketches in solids and using fillet on multiple edges at once. Sure...
  10. Replies
    11
    Views
    9,738

    Yes, something like that, but in the case of...

    Yes, something like that, but in the case of lofing there are no round edges, only straight lines from the larger text to the smaller text and the angle will be sharp. Tried this and ended up with a...
  11. Replies
    11
    Views
    9,738

    Subtract text from round shape for 3d printing

    Hello, I recently started using Blender cause 123dDesign & Meshmixer don't have all the options I need. I have some basic skills of fiddling around with the mesh
    My question is:
    How can I subtract...
  12. Replies
    4
    Views
    3,016

    I printed the model and 0.4 is an ok tolerance so...

    I printed the model and 0.4 is an ok tolerance so that the joint moves freely. I use 0.2 tolerance for interconnecting non-moving parts
  13. Thank you for advice. I wouldn't even have...

    Thank you for advice. I wouldn't even have bothered anymore if the scanner didn't tease me fo 5 hours and could test a few settings.
  14. Problem with Creaform HandyScan UNIScan 2011 model

    Hello, I rented a Creaform Handyscan UNIScan 2011 version and it came with a laptop that has VXElements as a scan software.

    It didn't worked at first but after 2 hours of trying some stuff like...
  15. Replies
    4
    Views
    3,016

    Thanks for information but I was talking about...

    Thanks for information but I was talking about STL-s that are already combined and optimized for 3d printing (like downloaded from thingiverse).
    In Netfabb there is a button called "ruler". It...
  16. Replies
    4
    Views
    3,016

    Measuring tolerances in STL

    Hello, I have a question regarding measuring tools for STLs. I am talking about premade STLs and not made by me.
    I have been working with 123D Design, Netfabb and Meshmixer for 3 months but none of...
  17. Replies
    21
    Views
    20,992

    In the last picture I posted (page 2), above the...

    In the last picture I posted (page 2), above the red line and just after the corner there is a bulge appearing. Below the red line the print is without acceleration and above with default...
  18. Replies
    21
    Views
    20,992

    Simplify 3D The problem is that when I up the...

    Simplify 3D
    The problem is that when I up the speed (as seen above the red line) there is a bulge appearing right after the sharp corner. That happens to all the prints.
  19. Replies
    21
    Views
    20,992

    Yes, we used the same filament. I was talking...

    Yes, we used the same filament. I was talking about the bulge that appears after sharp corners. The Z seam is where we put it (on another face of the bag handle).
    The story of our FFCP is a little...
  20. Replies
    21
    Views
    20,992

    More troubleshooting: 8999 click to enlarge

    More troubleshooting:
    8999
    click to enlarge
  21. Replies
    21
    Views
    20,992

    After a lot of tests and calibration we found out...

    After a lot of tests and calibration we found out that there is inconsistent movement to the X and Y rods.
    This could be because of bearings or belts. Don't know yet.

    Edit: Saw on a lot of forums...
  22. Replies
    5
    Views
    4,403

    Someone had this problem and still no solution...

    Someone had this problem and still no solution
    http://forums.reprap.org/read.php?178,509378
  23. Replies
    21
    Views
    20,992

    The bulge almost disappeared after changing some...

    The bulge almost disappeared after changing some JKN values and acceleration.
  24. Replies
    21
    Views
    20,992

    Update: I found the culprit.. it's the...

    Update:
    I found the culprit.. it's the acceleration
    Left one is without acceleration and right one with acceleration.
    ...
  25. Replies
    21
    Views
    20,992

    Yes, the bag handle was printed standing up and...

    Yes, the bag handle was printed standing up and the coat hangers on one side.
    For the handle the point for the Z scar is where it's supposed to be. That bulge is not on the exact opposite face, it...
Results 1 to 25 of 37
Page 1 of 2 1 2