Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    17
    Views
    1,103

    PrusaSlicer 2.3.0 has downloadable profiles one...

    PrusaSlicer 2.3.0 has downloadable profiles one is a Ender 5

    Click Configuration Tab > Select Configuration Wizard > Select Other Vendors and the Creality check box
    Then select Creality FFF and...
  2. Replies
    17
    Views
    1,103

    Was looking for this could not find so did not...

    Was looking for this could not find so did not post previously

    16351

    While 3D Printing this Laptop Stand at .28mm layer height i find that the area shaded in green has a texture as that of...
  3. Replies
    17
    Views
    1,103

    Everyone has different opinions on this subject,...

    Everyone has different opinions on this subject, I have never tried Simpily3d simply because it does not have a 30 day trial or reduced functionality test program.
    Plus the initial cost is out of my...
  4. Replies
    17
    Views
    1,103

    I started using Cura though wanting better...

    I started using Cura though wanting better quality I started using PrusaSlicer 2.3.0.

    This sweet slicer that has Slic3r roots will stand above most Free Slicers and will even put some expensive...
  5. Did you download Ender 5 plus using. Select...

    Did you download Ender 5 plus using.
    Select Ender 5 Plus 3D Printer
    Click Configuration > Click Configuration Wizard ...
    Click Other Vendors Check the box Creality select Creality Ender-5 Plus to...
  6. Looks to me like you are printing the infill with...

    Looks to me like you are printing the infill with a percentage. this could be normal.
    To correct choose infill as solid or at least above 75%.
  7. Replies
    5
    Views
    800

    It seem like I am always forgetting this one

    It seem like I am always forgetting this one
  8. Replies
    1
    Views
    292

    My first to Prints with PLA I set the temp from...

    My first to Prints with PLA I set the temp from 192-196C.

    After replacing hot-end heater and thermister. Now 3D Print from 200-208C using the same PLA.
  9. Replies
    5
    Views
    800

    This is called layer shifting. It is caused by...

    This is called layer shifting.

    It is caused by a few mechanical adjustments or sticky grease on your smooth rods.
    XY axis belts too loose or too tight, V-Ref current incorrectly adjusted. Bad...
  10. Replies
    4
    Views
    583

    It has been a while since using Cura mostly use...

    It has been a while since using Cura mostly use PrusaSlicer 2.3.0 now.

    Looked In Cura 4.8.0 and it is called Infill Overlap Percentage and Infill Overlap
  11. Replies
    4
    Views
    479

    It could be that the smaller model just needs to...

    It could be that the smaller model just needs to be printed slower on your 3D Printer.

    However I doubled the set print speed on my 3D Printer an dropped the nozzle temp to 208C
  12. Replies
    4
    Views
    583

    What is you infill percentage set to. This...

    What is you infill percentage set to.


    This looks vaguely familiar.
    Set your perimeter "vertical shells" to 2 or 3 walls printing perimeter first followed by printing infill with overlay to .025
  13. Replies
    4
    Views
    479

    I printed CE3PRO_cableChain_link_v3.gcode...

    I printed CE3PRO_cableChain_link_v3.gcode and there is nothing wrong with your sliced G-code.
    Therefore it must be have something to do with filament extrusion, clogged extruder, stepper missteps or...
  14. I built an enclosure with a single sheet if...

    I built an enclosure with a single sheet if plywood it has been working for 4 years.
    The cost was the price of one sheet of plywood and some wood glue a few nails a couple of plastic sheets for...
  15. Replies
    2
    Views
    498

    Do you have more information. Post STL of Flag,...

    Do you have more information.
    Post STL of Flag, post your Cura settings ect...
  16. Replacing the Fans Power Mosfet is a simple...

    Replacing the Fans Power Mosfet is a simple process an only requires unsoldering 3 terminals then re-solder.
  17. I would test the Power Supply by disconnecting...

    I would test the Power Supply by disconnecting the Supply leads from the 3D Printer an measure the voltage.

    Reconnect and measure the voltage at the Power Supply and the controller if there is a...
  18. Replies
    2
    Views
    537

    Your posted image suggests under extrusion,...

    Your posted image suggests under extrusion, Stepper slippage clogged nozzle ect...

    Post your slicers model settings
  19. Replies
    12
    Views
    1,991

    Using my slicer I can select a Seam Position of...

    Using my slicer I can select a Seam Position of Random then the Start Seam becomes invisible into this random starting position.
  20. Replies
    7
    Views
    1,224

    Maybe I misunderstood, Can you home or Level ...

    Maybe I misunderstood,
    Can you home or Level the 3D Printer without hitting the bed or Doe it hit the bed only when 3D Print starts.
  21. Replies
    12
    Views
    2,141

    Please read this web site...

    Please read this web site
  22. This could be a sign of moisture absorbed into...

    This could be a sign of moisture absorbed into the filament try a different roll of filament.
  23. Replies
    7
    Views
    1,224

    Hello: Colorado Have you tried to reset your...

    Hello: Colorado

    Have you tried to reset your 3D Printer settings to Factory Defaults.

    Your LCD has a setting to reset to factory settings or you can sent the following.
    M502 // Reset to...
  24. Replies
    12
    Views
    2,141

    Using Hair Spray can help, Or printing closer to...

    Using Hair Spray can help, Or printing closer to the print bed by 0.1mm can also help with adhesion.

    Sometime I print on vinyl transfer Paper Tape to help with curvier models.
  25. Replies
    5
    Views
    2,577

    Cura has the ability to change at Z

    Cura has the ability to change at Z
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4