Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.00 seconds.

  1. Make a video of this, Upload to a share like...

    Make a video of this, Upload to a share like google drive.
    You can then post a link to the share here.
  2. Replies
    9
    Views
    180

    When I started Out used these lines of code to...

    When I started Out used these lines of code to adjust my Proximity Sensor to work.
    These are a modified Code from Marlin 1.1.9BF to work with Marlin 2.
    Adjusted them with your offset for you to...
  3. Replies
    9
    Views
    180

    Your offset is wrong, post the error message...

    Your offset is wrong, post the error message exactly.
  4. Replies
    9
    Views
    180

    After looking found these could be tested your...

    After looking found these could be tested your end.

    #define NOZZLE_TO_PROBE_OFFSET { 43, 20, 0 }

    #define X_BED_SIZE 200
    #define Y_BED_SIZE 195

    #define X_MAX_POS 200
    #define Y_MAX_POS 195...
  5. Replies
    9
    Views
    180

    If you post your Bed size and the location of the...

    If you post your Bed size and the location of the nozzle from the proximity sensor using Marlins offset parameters.

    Then upload your Configuration.h file to a share program like google drive and...
  6. Below is a sample of Z-Stripping Model on left...

    Below is a sample of Z-Stripping
    Model on left is with tape model on right is without tape.
    14182



    Z-Stripping is caused when the Lead-screw warbles as it spins, causing the different layer...
  7. On my 3D Printer getting Z-Stripping which kind...

    On my 3D Printer getting Z-Stripping which kind of looks like what I see on the image you posted.

    To solve this problem I wrapped a single wrap of electricians tape on the lead-screw and press it...
  8. Replies
    4
    Views
    220

    Try ...

    Try

    https://cults3d.com/en/collections/useful-3d-printed-coronavirus-covid19-tool

    However I could not 3D Print a water nozzle without leaking, do not believe I would Trust with a virus that...
  9. Well I had a problem that had the same looks, ...

    Well I had a problem that had the same looks,
    it was because when setting up a new slicer forgot to set the filament diameter.

    As the default filament Dia is 3mm was getting under extrusion on...
  10. Replies
    1
    Views
    120

    Could be a bad X-Axis Driver, Could be the...

    Could be a bad X-Axis Driver, Could be the Stepper motor V-Ref needs to be adjusted, or a Bad Stepper Motor.

    You could switch the XY Stepper motors to see if the problem moves or remains constant,...
  11. I try not to recommend and only state what works...

    I try not to recommend and only state what works for my 3D Printer. Sometime I will state that the temperatures could be + or - from what is stated.

    This is so hard to do because every one has...
  12. Replies
    4
    Views
    465

    When I look at the image showing the letter Z I...

    When I look at the image showing the letter Z I see a rectangle, this tells me the you should measure your test cube.
    And do a calibration for your steps.

    ...
  13. Replies
    1
    Views
    414

    A Photo will help>

    A Photo will help>
  14. Replies
    2
    Views
    452

    Post you slicer settings, include material your...

    Post you slicer settings, include material your are using and what Slicer you are using...
  15. Thread: Mpcnc

    by Roberts_Clif
    Replies
    44
    Views
    8,765

    Think I missed this question. No I am using a ...

    Think I missed this question.

    No I am using a Dewalt DW660
  16. Replies
    8
    Views
    991

    Post the settings you are using for Cura, if...

    Post the settings you are using for Cura, if these settings are off it can ruin your entire model.
  17. Replies
    8
    Views
    991

    You are correct, Me Too. Though the more...

    You are correct, Me Too.

    Though the more information you give us about your 3D Printer and setup the easier it will be for someone to help.
  18. Replies
    8
    Views
    991

    I believe this subject has ran its course many...

    I believe this subject has ran its course many times over, thereby loosing interest for many 3D Printer users.
    I am here to see if we can find out why your Ultimaker is not printing better models at...
  19. Replies
    8
    Views
    991

    At what speed do you normally print using Cura...

    At what speed do you normally print using Cura Speed percentage or millimeters per second^3.
    Would also help to answer your question if we knew what filament you print with and what temperatures...
  20. I found it in all versions of marlin 1.1.x that I...

    I found it in all versions of marlin 1.1.x that I have programmed for My 3D Printer.
  21. Are you looking for #define MBL_Z_STEP 0.025 ...

    Are you looking for
    #define MBL_Z_STEP 0.025 // Step size while manually probing Z axis.
  22. Replies
    3
    Views
    438

    If you have the sense you will never let anyone...

    If you have the sense you will never let anyone take out a loan in your name.
    Don;t you know that the second they take out the load YOU are responsible to pay it back.

    And if they do take out a...
  23. Replies
    5
    Views
    483

    Hell! Never walk alone in any large city....

    Hell!

    Never walk alone in any large city. Especially at night.
  24. Replies
    7
    Views
    945

    The Hictop 3DP12 Prusa i3 3D Printer...

    The Hictop 3DP12 Prusa i3 3D Printer I purchased has been discontinued and is no longer being sold.

    Hictop has a parts list and assembly manual you could still make this 3D Printer and download...
  25. Replies
    10
    Views
    1,398

    I also find that cleaning the Bed with isopropyl...

    I also find that cleaning the Bed with isopropyl alcohol help me greatly in keeping good 1st layer adhesion with my bed material.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4