Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    136

    I place my filament in an average storage...

    I place my filament in an average storage container, with a moisture eliminator that was purchased for a local dollar store.
    My filament in some cases is up to 3.5 years old and still printing...
  2. Replies
    2
    Views
    525

    Looks like a clogged Ho-tend, This could be from...

    Looks like a clogged Ho-tend, This could be from the Teflon Tube melting or over heated filament that will not extrude.

    A good cleaning of your hot-end will solve this problem
  3. I would test End-stops using M119: Endstop...

    I would test End-stops using M119: Endstop States.

    Connect the 3D Printer using the USB to your computer and using terminal mode for 3D Printers with a capable slicer.
  4. Replies
    2
    Views
    552

    I would start by measuring the Power Supply...

    I would start by measuring the Power Supply voltage.
    Then would move to see if your computer could make a connection to the controller via USB..
    The display is not needed to print via a USB...
  5. The jumpers are determined by the step you are...

    The jumpers are determined by the step you are wanting.
    "Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step"

    DRV8825 Stepper Motor Driver Carrier,...
  6. I have never used the glcd tester, though if you...

    I have never used the glcd tester, though if you post more information about your DIY 3D Printer the forum and I will help you to solve.
    Have worked with Marlin configuring most versions 1.x.x -...
  7. Replies
    9
    Views
    2,621

    I installed my Fusion 360 free for Personal,...

    I installed my Fusion 360 free for Personal, Hobby Use using the link attached.
    Though have only created less than a dozen models over the last 4 years it still work every time I design another...
  8. Replies
    0
    Views
    130

    TPM 2.0 Compatiable Motherboard

    Looking to build my Newest Computer using an Intel Core i5-10600KA Comet Lake 6-Core 4.1 GHz LGA 1200 125W Desktop Processor Intel UHD Graphics 630
    16538
    Can someone direct me to a Good TPM 2.0...
  9. Replies
    13
    Views
    1,786

    This is nearly exactly what happened to my 3D...

    This is nearly exactly what happened to my 3D Prints though the clog was because of a throat with a PTFE liner slid into to nozzle Note the nozzle in the Image on right. you will see the PTFE tubing...
  10. Replies
    1
    Views
    948

    Post slicer setting, slicer an version

    Post slicer setting, slicer an version
  11. Replies
    2
    Views
    1,195

    I would also set the starting position to random....

    I would also set the starting position to random.

    16438
  12. Replies
    3
    Views
    756

    This could be simple as adjustment of retraction...

    This could be simple as adjustment of retraction on Z-Hop
  13. Replies
    0
    Views
    611

    3D Print Boards

    We are a new 3D print forum looking for good 3D Printer users become a member and take a look around, or just read as a quest.
  14. Replies
    13
    Views
    1,786

    Please Post image from top downward

    Please Post image from top downward
  15. Replies
    17
    Views
    2,272

    PrusaSlicer 2.3.0 has downloadable profiles one...

    PrusaSlicer 2.3.0 has downloadable profiles one is a Ender 5

    Click Configuration Tab > Select Configuration Wizard > Select Other Vendors and the Creality check box
    Then select Creality FFF and...
  16. Replies
    17
    Views
    2,272

    Was looking for this could not find so did not...

    Was looking for this could not find so did not post previously

    16351

    While 3D Printing this Laptop Stand at .28mm layer height i find that the area shaded in green has a texture as that of...
  17. Replies
    17
    Views
    2,272

    Everyone has different opinions on this subject,...

    Everyone has different opinions on this subject, I have never tried Simpily3d simply because it does not have a 30 day trial or reduced functionality test program.
    Plus the initial cost is out of my...
  18. Replies
    17
    Views
    2,272

    I started using Cura though wanting better...

    I started using Cura though wanting better quality I started using PrusaSlicer 2.3.0.

    This sweet slicer that has Slic3r roots will stand above most Free Slicers and will even put some expensive...
  19. Did you download Ender 5 plus using. Select...

    Did you download Ender 5 plus using.
    Select Ender 5 Plus 3D Printer
    Click Configuration > Click Configuration Wizard ...
    Click Other Vendors Check the box Creality select Creality Ender-5 Plus to...
  20. Looks to me like you are printing the infill with...

    Looks to me like you are printing the infill with a percentage. this could be normal.
    To correct choose infill as solid or at least above 75%.
  21. Replies
    5
    Views
    1,091

    It seem like I am always forgetting this one

    It seem like I am always forgetting this one
  22. Replies
    1
    Views
    388

    My first to Prints with PLA I set the temp from...

    My first to Prints with PLA I set the temp from 192-196C.

    After replacing hot-end heater and thermister. Now 3D Print from 200-208C using the same PLA.
  23. Replies
    5
    Views
    1,091

    This is called layer shifting. It is caused by...

    This is called layer shifting.

    It is caused by a few mechanical adjustments or sticky grease on your smooth rods.
    XY axis belts too loose or too tight, V-Ref current incorrectly adjusted. Bad...
  24. Replies
    4
    Views
    731

    It has been a while since using Cura mostly use...

    It has been a while since using Cura mostly use PrusaSlicer 2.3.0 now.

    Looked In Cura 4.8.0 and it is called Infill Overlap Percentage and Infill Overlap
  25. Replies
    4
    Views
    677

    It could be that the smaller model just needs to...

    It could be that the smaller model just needs to be printed slower on your 3D Printer.

    However I doubled the set print speed on my 3D Printer an dropped the nozzle temp to 208C
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4