Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    39

    3D Printed Home in Austin, Texas

    Building Was 3D-Printed in 27 Hours, and It's Designed to Help the Homeless
    https://austin.curbed.com/2019/9/10/20858924/austin-homeless-tiny-house-3d-printing
  2. Thank You! I will Print a Couple for Prevent...

    Thank You!

    I will Print a Couple for Prevent Homeless Pets.
  3. I too am impressed! Would like to see a more...

    I too am impressed!

    Would like to see a more detailed image.

    Actually would like to try an print one even though I only have a one nozzle 3D Printer.
  4. If you have more questions post we will do our...

    If you have more questions post we will do our best to help you answer them.
  5. It should be under the Control menu,

    It should be under the Control menu,
  6. Replies
    3
    Views
    275

    When My 3D Printer does this it is because it has...

    When My 3D Printer does this it is because it has not been homed.

    Auto Home the 3D Printer and it should know where the end_stops are.
  7. From the Menu it should say something like...

    From the Menu it should say something like Restore fail-safe. Then Store settings.
  8. Replies
    17
    Views
    23,335

    I Heat the bed to 96C and lift the old bed...

    I Heat the bed to 96C and lift the old bed surface, though this method almost always leaves some of sticky glue surface.
    Then using a spatula on my Aluminum hotbed, I lightly scrape the glue from ...
  9. Replies
    2
    Views
    593

    Post more information, Nozzle temp, Bed Temp ect....

    Post more information, Nozzle temp, Bed Temp ect.

    And post a photo we can help you get to a print you can use.
  10. Replies
    6
    Views
    1,373

    Are trying to print a .2mm wall, Do you have a...

    Are trying to print a .2mm wall, Do you have a .2mm nozzle or smaller. I would really like to see this.
  11. I would start by resetting the Ender 3 to factory...

    I would start by resetting the Ender 3 to factory settings.


    M502 ;Restore Firmware Defaults settings.
    M500 ;Save settings to EEProm

    Then I would Check all end-stop switches with a M119...
  12. That did not take you long. If you need other...

    That did not take you long.

    If you need other help post we will be here.
  13. Sounds like one of the end stop switches. With...

    Sounds like one of the end stop switches.
    With the Nozzle in the center of bed send

    M119 - Endstop States

    Then check each end stop pressing the switch and sending the End-stop States code.
  14. In order to change the extruder from its current...

    In order to change the extruder from its current extrusion of 150mm to 100 it has to be reduced by 1.3 or 50mm
    multiplying by 2/3rds or .666 gives us 400 + .6666 = 266.664


    #define...
  15. You must have a really good enclosure. My...

    You must have a really good enclosure.
    My enclosure allows the smell even with the vent fan going an as soon as I open the door of the enclosure the smell increases.
    Especially when printing with...
  16. Every filament I have printed with has its...

    Every filament I have printed with has its indiviual smells.

    Do not know why you can not smell it but they all smell.

    https://ultimaker.com/download/13079/SDS%20ABS.pdf
  17. Thread: Mpcnc

    by Roberts_Clif
    Replies
    42
    Views
    5,153

    Hello again;; I discovered today that the...

    Hello again;;

    I discovered today that the longer Stepper motor cables I purchased from California.
    Are in fact being shipped from mainland china, so it will be quite some time before I see the...
  18. I Too have a home Made enclosure, with a outdoor...

    I Too have a home Made enclosure, with a outdoor thermometer behind each 3D Printer and the temperature stays pretty close to 100F .
    I do not have to do anything, however I have a bathroom vent with...
  19. Thread: Mpcnc

    by Roberts_Clif
    Replies
    42
    Views
    5,153

    Oh Yes! There are many free and paid alike,...

    Oh Yes!

    There are many free and paid alike, maybe even more than for 3D Printers.
  20. Replies
    19
    Views
    1,511

    Your images display perfectly. Here is a copy of...

    Your images display perfectly.
    Here is a copy of one.

    13356

    As for the lines starting up about 1/3 of the model being printed this could be a multitude of problems.
    This could happen because...
  21. Replies
    19
    Views
    1,511

    I purchase Moisture Absorbent at the local Dollar...

    I purchase Moisture Absorbent at the local Dollar Store and toss it into the rubber storage container that's used to store the Filament this way it is always moisture free.
  22. Thread: Mpcnc

    by Roberts_Clif
    Replies
    42
    Views
    5,153

    I am still looking for a Control case, the one I...

    I am still looking for a Control case, the one I found and 3D Printed is in fact a horrible 3D Printing Control case, it is so thin you can virtually see thew it.
    And I do do want to waste my time...
  23. Replies
    19
    Views
    1,511

    I have to agree, though before I had learned this...

    I have to agree, though before I had learned this information I had purchased many rolls of ABS, now had to learn how to print it as wasting is not in my nature.

    After many prints have learned...
  24. Thread: Mpcnc

    by Roberts_Clif
    Replies
    42
    Views
    5,153

    Today I decide to test test main floor platform...

    Today I decide to test test main floor platform for level.
    With ~6mm above the bed then lowered the Tool plate 6mm on all four corners an dead center the platform.
    Being really close to the main...
  25. Replies
    19
    Views
    1,511

    I created a single sheet plywood case for dual 3D...

    I created a single sheet plywood case for dual 3D Printers, I read that this is the easiest way to keep ABS from warping.

    I print with a bed temp of 96C and a hot-end temp of 236C.
    I start...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4