Close



Dig deeper, search our News website




Search:

Type: Posts; User: airscapes

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    146

    Gravity feed spool holder with roller bearing so...

    Gravity feed spool holder with roller bearing so filament move with virtual no force required. If you extruder drive is not just spring loaded, adjust the tension with a test print running. Loosen...
  2. Replies
    5
    Views
    582

    Caleb1, I don't have that printer but have used ...

    Caleb1, I don't have that printer but have used Ninjaflex and just tried NinjaTech Cheetah. The cheetah has is not as stretchy as ninjaflex and prints very well. Depending on your extruders...
  3. No, not really sealed.. probably nose blind ..

    No, not really sealed.. probably nose blind ..
  4. Sorry, what I meant was with the enclosure, the...

    Sorry, what I meant was with the enclosure, the room does not smell.. Of maybe I have become nose blind..
  5. My printer is in an extra bedroom.. with my home...

    My printer is in an extra bedroom.. with my home built enclosure, there is no need to vent anything. it does not smell, and it stays at 100F with heat and heated bed.. youi all make this much more...
  6. For my purposes I find ABS to be much more rigid...

    For my purposes I find ABS to be much more rigid than any of the Nylon I have used (6xx, 910, EPA) or PETG. Also the ABS MakerGear sells prints very nicely and is easy to print especially with the...
  7. I have a home made enclosure with a small heater...

    I have a home made enclosure with a small heater and an InkBird thermostat. With the thermostat set at 100F the small heater and heated bed keep the enclosure at 100F without external venting. I...
  8. Replies
    19
    Views
    883

    Esun is fine, just not always as consistent in...

    Esun is fine, just not always as consistent in diameter. I use Esun all the time PLA + PETG and ABS.. just saying there is higher quality and it does make a difference.
  9. Replies
    19
    Views
    883

    In defense of ABS, it works really well in an...

    In defense of ABS, it works really well in an enclosure that is kept at 100F while printing and a bed at 110C. I have been using it a LOT for functional parts I design. The higher quality ABS works...
  10. Replies
    3
    Views
    228

    would guess it is a printer problem. PETG likes...

    would guess it is a printer problem. PETG likes the initial starting height just right so it is not over crushed or too high with a bed temp of 70C. .02mm too high and you have adhesion issues. ...
  11. Can not speak on cura but if one works then I...

    Can not speak on cura but if one works then I don't think your issue is cura. PETG is very particular about over all layer height. Starting height has to be perfect or you are in for trouble. Each...
  12. Well I bought Feb of 2018 when 4.01 was out and...

    Well I bought Feb of 2018 when 4.01 was out and it works very well once you learn it. They updated to 4.1 this year and screwed the pooch big time.. Think someone else may have bought them, hired a...
  13. First off, what version of S3D are you using? ...

    First off, what version of S3D are you using? They broke the crap out of it when they went to 4.1. I had a feeling this would happen and never upgraded.
    Go to S3D forum as there are so many bugs...
  14. Replies
    11
    Views
    1,299

    who sells filament without labels? May want to...

    who sells filament without labels? May want to try some name brand stuff.. Esun makes good filament at decent prices. .. for future reference.
  15. Replies
    11
    Views
    1,299

    No idea why, but from what I have read on this...

    No idea why, but from what I have read on this forum the Ender 3 is a very poor designed and built printer. It does not help you but unfortunately you are on an up hill battle that you shouldn't...
  16. I know nothing of your slicer but it looks like...

    I know nothing of your slicer but it looks like something is not set correctly or if this is an internet model it could have errors in it. Sorry can not be of more help
  17. Replies
    21
    Views
    6,442

    Sounds like a fortune cookie.. guess it is a bot

    Sounds like a fortune cookie.. guess it is a bot
  18. Replies
    4
    Views
    873

    I only have the M2 so I just use very low infill...

    I only have the M2 so I just use very low infill when I have to use support when printing with Petg as it is not suited for support as you know. I set my XY speed in S2D to 200 rather than the...
  19. Replies
    4
    Views
    573

    Have you tired a skirt with about 7 outlines a 2...

    Have you tired a skirt with about 7 outlines a 2 layers .03 from the part?
  20. Go for it! The great thing about 3D design and...

    Go for it! The great thing about 3D design and fabrication is you can do things like this for little to no cost. You will probably get very frustrated with the software trying to figure out how to...
  21. This is what I would call normal for FFF .. It...

    This is what I would call normal for FFF .. It isn't injection molding..

    Totally different printer and Simplified 3d slicer.. can I do a zhop to reduce this, yes but it will slow down my print...
  22. Replies
    8
    Views
    1,920

    Sounds like a plan! Please keep us in the loop as...

    Sounds like a plan! Please keep us in the loop as you progress.
  23. Replies
    5
    Views
    1,101

    I know nothing of your slicer or printer, but is...

    I know nothing of your slicer or printer, but is there some reason you don't just flip the model to lay flat on the bed and then there is no need for support?
  24. Replies
    8
    Views
    1,920

    I think as you learn how 3d fabrication works you...

    I think as you learn how 3d fabrication works you will realize what you can and can not do within reason. But first you must learn to; Sit up, crawl, stand, walk, then you can run..
  25. Your print bed is 8 feet long?? or 8 inches long?...

    Your print bed is 8 feet long?? or 8 inches long? Google 3D printing Filament type and usage..
Results 1 to 25 of 181
Page 1 of 8 1 2 3 4