Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    203

    Does Folgertech have a Marlin Configuration.h...

    Does Folgertech have a Marlin Configuration.h file

    Post your Entire Marlin to a share like Google Drive post the lnik here will take a look.
  2. Replies
    6
    Views
    203

    If home is Left Front then X-Axis end stop is an...

    If home is Left Front then X-Axis end stop is an max, Y-Axis is at min
    From what you posted I believe all you have to do is.

    // Direction of end-stops when homing; 1=MAX, -1=MIN

    #define...
  3. Replies
    6
    Views
    203

    OK so you have a question? I can not answer...

    OK so you have a question? I can not answer without asking a few myself to you.
    Would help if we knew something about your 3D Printer.
    1. Where is the Home 0,0,0 located on the bed.
    2. What style...
  4. Replies
    3
    Views
    196

    Watch this video on layer smoothing. ...

    Watch this video on layer smoothing.

    https://www.youtube.com/watch?v=gh5wC4Ti95s
  5. Replies
    1
    Views
    194

    Post a picture of your original switch along with...

    Post a picture of your original switch along with your new switches.

    Let the forum see someone will be able to help.
  6. Replies
    1
    Views
    128

    1.) No! I re-level my 3D Printer about every...

    1.) No! I re-level my 3D Printer about every three weeks or longer.

    2.) Print using a skirt

    3.) Set Z-Hop
  7. Replies
    10
    Views
    398

    Then I would suggest that the stepper motor cable...

    Then I would suggest that the stepper motor cable could be intermittent an may need testing / replacing
  8. Replies
    12
    Views
    527

    You are welcome. If you need any other help...

    You are welcome.

    If you need any other help Post.
  9. Replies
    10
    Views
    398

    A point about Marlin firmware . FYI - Marlin...

    A point about Marlin firmware .
    FYI - Marlin has a safety it the hot-end is not up to 170C it will not turn.


    #define PREVENT_COLD_EXTRUSION
    #define EXTRUDE_MINTEMP 170
  10. Replies
    10
    Views
    398

    I would check the alignment of the Extruder Gear....

    I would check the alignment of the Extruder Gear. Could be catching of the extruder assembly.
  11. Replies
    12
    Views
    527

    They did Update this Code!! // Set the...

    They did Update this Code!!

    // Set the boundaries for probing (where the probe can reach).
    #define MIN_PROBE_EDGE_LEFT MIN_PROBE_EDGE + 10
    #define MIN_PROBE_EDGE_RIGHT (X_BED_SIZE -...
  12. Replies
    2
    Views
    120

    Make a video of this, Upload to a share like...

    Make a video of this, Upload to a share like google drive.
    You can then post a link to the share here.
  13. Replies
    12
    Views
    527

    When I started Out used these lines of code to...

    When I started Out used these lines of code to adjust my Proximity Sensor to work.
    These are a modified Code from Marlin 1.1.9BF to work with Marlin 2.
    Adjusted them with your offset for you to...
  14. Replies
    12
    Views
    527

    Your offset is wrong, post the error message...

    Your offset is wrong, post the error message exactly.
  15. Replies
    12
    Views
    527

    After looking found these could be tested your...

    After looking found these could be tested your end.

    #define NOZZLE_TO_PROBE_OFFSET { 43, 20, 0 }

    #define X_BED_SIZE 200
    #define Y_BED_SIZE 195

    #define X_MAX_POS 200
    #define Y_MAX_POS 195...
  16. Replies
    12
    Views
    527

    If you post your Bed size and the location of the...

    If you post your Bed size and the location of the nozzle from the proximity sensor using Marlins offset parameters.

    Then upload your Configuration.h file to a share program like google drive and...
  17. Below is a sample of Z-Stripping Model on left...

    Below is a sample of Z-Stripping
    Model on left is with tape model on right is without tape.
    14182



    Z-Stripping is caused when the Lead-screw warbles as it spins, causing the different layer...
  18. On my 3D Printer getting Z-Stripping which kind...

    On my 3D Printer getting Z-Stripping which kind of looks like what I see on the image you posted.

    To solve this problem I wrapped a single wrap of electricians tape on the lead-screw and press it...
  19. Replies
    4
    Views
    294

    Try ...

    Try

    https://cults3d.com/en/collections/useful-3d-printed-coronavirus-covid19-tool

    However I could not 3D Print a water nozzle without leaking, do not believe I would Trust with a virus that...
  20. Well I had a problem that had the same looks, ...

    Well I had a problem that had the same looks,
    it was because when setting up a new slicer forgot to set the filament diameter.

    As the default filament Dia is 3mm was getting under extrusion on...
  21. Replies
    1
    Views
    140

    Could be a bad X-Axis Driver, Could be the...

    Could be a bad X-Axis Driver, Could be the Stepper motor V-Ref needs to be adjusted, or a Bad Stepper Motor.

    You could switch the XY Stepper motors to see if the problem moves or remains constant,...
  22. I try not to recommend and only state what works...

    I try not to recommend and only state what works for my 3D Printer. Sometime I will state that the temperatures could be + or - from what is stated.

    This is so hard to do because every one has...
  23. Replies
    4
    Views
    524

    When I look at the image showing the letter Z I...

    When I look at the image showing the letter Z I see a rectangle, this tells me the you should measure your test cube.
    And do a calibration for your steps.

    ...
  24. Replies
    1
    Views
    440

    A Photo will help>

    A Photo will help>
  25. Replies
    2
    Views
    484

    Post you slicer settings, include material your...

    Post you slicer settings, include material your are using and what Slicer you are using...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4