Close



Dig deeper, search our News website




Search:

Type: Posts; User: ohms

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    6,386

    ahh pin 9 did the trick. Thanks

    ahh pin 9 did the trick. Thanks
  2. Replies
    4
    Views
    6,386

    it is a rambo 1.2b board with marlin firmware....

    it is a rambo 1.2b board with marlin firmware. Forgot to include that in there.
  3. Replies
    4
    Views
    6,386

    heater pin numbers

    Hi, I was installing the e3d hotend with a new heater cartridge and thermocouple. I think I accidentally changed the pin number for #define HEATER_0_PIN. I have it set to 8 right now. is this...
  4. Yes, I did. Do you know if I have to use a...

    Yes, I did. Do you know if I have to use a specific version or flavor of the firmware? I just edited the one that came with the printer
  5. hey so I tried following those instructions so no...

    hey so I tried following those instructions so no I have the thermocouple board power connected to the top right pin from the picture and ground to the pin right below it and signal to the top left...
  6. ahh thanks, that helps out a lot, I should be...

    ahh thanks, that helps out a lot, I should be able to get it working following that discussion, thanks
  7. connecting external thermocouple board to rambo board

    Hi, I bought the e3d volcano hotend with the k-type thermocouple and thermocouple board, but I'm not sure on how to connect the external thermocouple...
  8. Replies
    3
    Views
    2,907

    converting to different filament diameter

    Hi, I'm curious about what I would need to do to convert a printer from using 1.75mm filament to 2.85mm? Is it simply switching the hotend? how much work would this be?
  9. Replies
    5
    Views
    2,853

    I actually got it straight from airwolf. What I'm...

    I actually got it straight from airwolf. What I'm confused about is that it printed well for a while, then suddenly I ran into this problem
  10. Replies
    5
    Views
    2,853

    PLA extrusion problem

    Hi, I started printing in PLA and everything was fine, but recently, the filament stopped extruding continuously through the nozzle even though I didn't change any of the settings. I'm pretty sure it...
  11. Thread: airwolf HD parts

    by ohms
    Replies
    3
    Views
    3,158

    I downloaded that software, but I can only add...

    I downloaded that software, but I can only add files to it. there are no pre-uploaded files on it that I can see.
  12. Thread: airwolf HD parts

    by ohms
    Replies
    3
    Views
    3,158

    airwolf HD parts

    does anyone know where I can download the cad files for the 3d printed parts that come with the airwolf HD printer?
  13. Replies
    5
    Views
    3,371

    fjnamtiw, I actually don't know to what you're...

    fjnamtiw, I actually don't know to what you're referring to. How do I go about doing that and what does it do? I have put in a new bolt and feeding tube. I do have to mention that I bought it used...
  14. Replies
    5
    Views
    3,371

    I have cleaned the extruder assembly but no...

    I have cleaned the extruder assembly but no change. I'm thinking that maybe the hobbed bolt might be damaged even though I couldn't really tell. I have ordered a new one so now I just have to wait...
  15. Replies
    5
    Views
    3,371

    PLA extrusion not consistent

    I have an airwolf HD. I'm trying to print on black pla from matterhackers, but it wont extrude evenly. I'll try to extrude into open air for 100mm and it will start extruding, but then extruder...
  16. Replies
    2
    Views
    1,720

    Thanks for the tips. Turned out to be an easy...

    Thanks for the tips. Turned out to be an easy fix. the extruder springs must have been damaged because I simply replaced them and the problem went away. Thanks
  17. Replies
    2
    Views
    1,720

    airwolf HD extruder clicking

    I have an airwolf HD printer. the extruder keeps clicking while trying to extrude chipping away at the filament and giving inconsistent extrusion. I have completely cleaned the nozzle and have also...
Results 1 to 17 of 17