Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Would like more information on the position of...

    Would like more information on the position of the model while 3D Printing.

    Though without any further information, i suspect that the area where the seam is located may not have a friction free...
  2. Replies
    8
    Views
    1,059

    The last lines of my startup g-code is always in...

    The last lines of my startup g-code is always in the Slicer

    M420 S1 ; Bed Leveling turned On
    M106 P1 S128 ; P1 = 2nd Fan set 50% Speed
    M220 S32.000000 Starting print speed
  3. Replies
    2
    Views
    805

    We read here you have a SN04 Proximity sensor, It...

    We read here you have a SN04 Proximity sensor, It would help if you stated what 3D Printer you have.
    A few pictures of your 3D Printer could also be helpful if they show optional hardware.
  4. Replies
    8
    Views
    1,059

    It appears you are doing every thing in the...

    It appears you are doing every thing in the correct order.

    Leveling the bed is kind of an Art until you have more experience under your belt some may fail an some will work.
    Some times you just...
  5. Replies
    1
    Views
    802

    I have used Cura 15.04.6 forever and have never...

    I have used Cura 15.04.6 forever and have never had a problem,
    Though to get better prints I now use Prusaslicer mostly newest version though all work fine for me.

    If you post STL files will...
  6. IS does not happen often though It could be that...

    IS does not happen often though It could be that you need to initialize your printer to factory defaults.
  7. Replies
    8
    Views
    7,685

    Sticky: Hello curious aardvark. My CoreXY in being...

    Hello curious aardvark. My CoreXY in being created from parts printed using this Thingiverse article. Hope it works out well.
  8. Replies
    1
    Views
    941

    I would start with watching this cleaning the...

    I would start with watching this cleaning the nozzle Video.

    I would start by heating the Nozzle to your last filament temp TPU an push remaining clogged TBU out with some.
    Then remember to...
  9. Replies
    17
    Views
    11,596

    I do not believe that we choose, I believe the...

    I do not believe that we choose, I believe the our pets choose us.
  10. The Driver chip module can be removed and...

    The Driver chip module can be removed and replaced , do not believe that the mother board is fried only Driver chip module.

    Modules are around $10 dollar or so. When replacing watch for pin...
  11. Replies
    1
    Views
    851

    Under extrusion could be you forgot to set the...

    Under extrusion could be you forgot to set the filament diameter in Cura.
  12. Replies
    17
    Views
    11,596

    Cat person!!!

    Cat person!!!
  13. Replies
    3
    Views
    1,343

    Now that we can remove the obvious, it could be...

    Now that we can remove the obvious, it could be determined that one or two other solutions could be tried.

    1: you could be experiencing over extrusion you could reduce the flow rate and see if...
  14. Replies
    2
    Views
    912

    I would download with Prusaslicer it has preset...

    I would download with Prusaslicer it has preset downloadable profiles for Ender 3D Printer this will eliminate any guess work setting up your slicer.
  15. Video It would be easier to help if one could see a...

    It would be easier to help if one could see a clear photograph .

    Let me take a guess, You should drop the Z-Offset to lower this offset by another -0.1
  16. Replies
    1
    Views
    1,587

    Starting a 3D Printing business is not easy...

    Starting a 3D Printing business is not easy unless you are a very proficient 3d Printer Operator and have learned to print almost perfect models.
  17. Replies
    3
    Views
    1,343

    It appears you have a visible seam, this can be...

    It appears you have a visible seam, this can be fixed by selecting a random seam.
  18. Replies
    3
    Views
    1,635

    Try again with this link for help here...

    Try again with this link for help here with more information maybe then I can help you more.
  19. It has been a long time sense using Slic3r I have...

    It has been a long time sense using Slic3r I have upgraded to Prusaslicer this little jewel was created from Slic3r it is one of the best free slicers ever.
    You should be able to import your Slic3r...
  20. Replies
    3
    Views
    1,635

    We can most likely help here...

    We can most likely help here is a link with some information browse then post again with any questions you have.
    Our interaction may take a few days before getting all the information to flash a...
  21. I use many different slicers, as it is up to the...

    I use many different slicers, as it is up to the user - me to determine which one works best for my 3D Printers...

    So guess you would like me to tell you what I have determined was best for my...
  22. It appears that your nozzle is a little to high...

    It appears that your nozzle is a little to high above the bed. Adjust using Z-Offset.
  23. Replies
    1
    Views
    891

    Clean your bed surface with 70% isopropyl alcohol...

    Clean your bed surface with 70% isopropyl alcohol or above,
    If this does not work then raise the bed temp to 100C for a couple minutes clean and try again.
  24. Hello Sam from Boston; I assume anyway. I see...

    Hello Sam from Boston; I assume anyway.

    I see you posted some of the information required to trouble shoot though would like more information.
    At what speed are you printing.
    What slicer are you...
  25. Replies
    8
    Views
    7,685

    Sticky: Great Work. Thank You.

    Great Work.

    Thank You.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4