Search:

Currently I am trying to print on this surface with no luck.
IdeaFormer 256x268mm Anycubic Kobra 3 Compatible 3D Printer Build Plate, Spring Steel PEO / PET Heat bed Sheet with Magnet Base.

...

Not sure exactly what I am looking for.

Well I see a solid layer below a interweaving mesh topped with a 2nd solid top layer.

This design looks like it could be difficult to 3D Print at 11mm^3...

You are welcome.

I have had New filament just removed from packaging cause me similar problems.
Though tuning a 3D Printer can be quite frustrating until you learn the process.

I starting...

You are welcome.

I have my 3D printer setup to print the first layer at 32% then the remaining layers at 72-82%.

This is relative to which slicer I am using Cura 15.04.6 prints at what I ...

Sometime it is not easy deduce the cause of a missed print.
Have had prints where the filament I was using was spliced with higher temperature filament and would clog the nozzle after removal of...

The only time I get is when I try to 3D Print the first layer too fast.
Sometimes 1st and 2nd layers then it will finish 3D printing perfectly.

Check the lead screws it sounds like the side making the most noise could have too much tension an could be out of alignment.
Once my 3D Printer the lead screw nut was not square with the threaded...

I do understand

I have printed on Vinyl transfer paper tape.

Will Vinyl transfer paper Hold my Part


https://youtu.be/qzWKE3TO9UU

Well I guess this shows that it will.

I remember when first a PEI build sheet thought would never get anything to stick until after printing ABS.
Then all my filament was sticking well, Also was told to use Hairspray that never worked...

OK every thing is working although the PEO-PET bed is not holding the PLA as well as expected any suggestions what I should do to correct...

After taking a real close look at my 3D Printers.
I have made a decision that there are so many loose parts that I need to do complete maintenance on all 3D Printers starting with Red my 1st...

Finally got the 1st 3D Printer working correctly, kind of, the bed adhesion is not even close to what I was expecting.
IdeaFormer 256x268mm Anycubic Kobra 3 Compatible 3D Printer Build Plate, Spring...

I have had a slow movement back into 3D Printing after about the same of time frame.
Purchased a Big Tree Tech SKR Pro V1.1 32bit Controller For my Home Brew CoreXY 3D Printer.

Have ordered three...

I have installed the first flexible magnetic stainless steel bed. The steel plates have much more sensitivity to my proximity sensor making them detect this plate 2mm before the Heated aluminum bed. ...

Hello been looking to see if there was anything I could do to help you.

I found the following information you might be well to read.

Aquila X3 bed probe not working in Marlin/MRiscoCProUI
...

I need to try a Magnetic build plate one of these days.

If you flashed your firmware then in order to figure out what went wrong you will need to post at least the configuration.h and configuration_Adj.h files.

This way we can see what is going on,...

Took a quick look using google
found this hope it helps

Here

The code looks almost exactly like startup code on my Hictop 3DP11/12's.
My Hictop which is almost exactly the same as an Ender 3...

I know that the Extruder stepper motor will not move filament until the Hotend is up the temp.

Though we need to determine if the stepper motor is actually moving.
Some how by hand or stepper...

I 3D Printed this nozzle box

19439

19440

I found on t https://www.printables.com/model/154769-nozzle-box

This was a fun project an as you can see turned out really good, an is more than...

I have a similar 3D Printer and had a block so bad that decided to replace everything.

Throat w/PTFE throat
Heater Block
Nozzle
12/24volt Heater (as I have 12v and 24V 3D Printers)
Thermister...

Yes they are called a Sock

Official Creality Ender 3 V2 Neo Silicone Sock

Have no ideal what you mean by derugulated.

However I have just had a similar problem after several hours of troubleshooting I have learned that the SD card was causing the problem.
I tested the...

hello

Use 210C for Nozzle and 55C for Bed temp with PLA+.
ALWAYS use a raft

When I have similar problems you are describing, I find that the PTFE tubing has deformed and needs to be replaced.

Pictures attached. Thought this may be causing your problems.

19431