Close



Dig deeper, search our News website




Search:

Type: Posts; User: Carrot_or_Stick

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    34
    Views
    28,908

    Lowes did for me, Home Depot wasn't interested.

    Lowes did for me, Home Depot wasn't interested.
  2. What did you end up doing with your i3v?

    What did you end up doing with your i3v?
  3. Replies
    13
    Views
    7,468

    Very interested in this! Can you keep us updated...

    Very interested in this! Can you keep us updated on your progress and thoughts?
  4. Replies
    13
    Views
    9,797

    OH MY GOD! I am not a smart man....I have been...

    OH MY GOD! I am not a smart man....I have been running the G29 command without any other items....just "G29".

    I thought that line specified the number of grid points per axis and the G29 command...
  5. Replies
    13
    Views
    9,797

    Yes I did, mine was set to 3 but when i tried 4...

    Yes I did, mine was set to 3 but when i tried 4 or 5 instead it does not change the number of points sampled. I tried clearing my eeprom before uploading my changed firmware with no success. I also...
  6. Replies
    13
    Views
    9,797

    Thanks for the info. I chose to go back to the...

    Thanks for the info. I chose to go back to the beckdac version and its very nice. SD card works again too (was broken on RC1). You know of anyway of increasing the ABL grid points from 3x3? I've...
  7. Replies
    13
    Views
    9,797

    Does that fork also contain all the safety...

    Does that fork also contain all the safety enhancements in the newer versions of marlin? Such as watchdog and thermal runaway protection?
  8. Try running a G92 E0 command to reset the...

    Try running a G92 E0 command to reset the extruder before you try to extrude the 100mm for the calibration test. The G92 E0 command resets the extruder.
  9. Replies
    6
    Views
    18,687

    Cables are correctly connected, and the Rumba...

    Cables are correctly connected, and the Rumba board does not have an on-board SD Memory Card slot. I will keep tooling around with this in my free time but since I use octopi it's not a massive deal....
  10. Replies
    6
    Views
    18,687

    Yes it does have 2 ribbon cables running to it....

    Yes it does have 2 ribbon cables running to it. However, if the 2nd cable wasn't connected correctly wouldn't I have more issues with the display? Anyway, thanks for your help, I'll check the...
  11. Replies
    6
    Views
    18,687

    Correct I have a Rumba (defined as board 80) set...

    Correct I have a Rumba (defined as board 80) set in my config.h file. Everything else works as expected aside from the SD card.
  12. Replies
    6
    Views
    18,687

    Cannot print from SD card

    I have the RepRap discount full graphics controller with a Rumba board but I cannot get my SD Card slot to work correctly. I'm currently running the Marlin RC (first version) and when I insert my...
  13. Replies
    7
    Views
    3,775

    I also run a G28 and then a G29 before each...

    I also run a G28 and then a G29 before each print. It's in the starting GCode in Sli3er
  14. Replies
    10
    Views
    28,186

    Thank you!

    Thank you!
  15. Replies
    10
    Views
    28,186

    Very nice! Where did you source your lead screws...

    Very nice! Where did you source your lead screws from? I have a bent guide rod and i'm looking to upgrade.
  16. Replies
    10
    Views
    28,186

    Generally speaking I have mostly seen people use...

    Generally speaking I have mostly seen people use them in a Bowden configuration.
  17. Replies
    10
    Views
    28,186

    1. When trying to fix an issue change ONE THING...

    1. When trying to fix an issue change ONE THING AT A TIME and then test that change to see if it helped.
    2. Do NOT use PLA parts in an enclosure....learning this the hard way right now.
    3. Learn...
  18. Replies
    5
    Views
    4,309

    For your banding issues you might want to look at...

    For your banding issues you might want to look at this post -
    http://3dprintboard.com/showthread.php?15818-How-I-fixed-Z-banding-on-my-12-quot-i3v-AL-Y-bed-and-solid-state-heat-bed-relay-PID
  19. Replies
    24
    Views
    17,206

    Printed out a test cube, thing came out to within...

    Printed out a test cube, thing came out to within .03mm of spec. Having no issues with Marlin RC so far.
  20. At the bottom of the first page I have a picture...

    At the bottom of the first page I have a picture posted of my setup. However, what you are saying is correct.
  21. Replies
    24
    Views
    17,206

    I have the full graphical LCD (reprap discount). ...

    I have the full graphical LCD (reprap discount). Your fix for the knob rotation worked great though it does apply universally, not an issue though.

    Also I was able to set my extra thermistor up...
  22. Replies
    6
    Views
    12,317

    Isn't that the name of the game anyway? Thank you...

    Isn't that the name of the game anyway? Thank you for the info!
  23. Replies
    6
    Views
    12,317

    Don't have any info but definitely interested in...

    Don't have any info but definitely interested in what you turn up. Good luck!
  24. Replies
    24
    Views
    17,206

    Well I got it flashed to my rumba board and it's...

    Well I got it flashed to my rumba board and it's printing out Benchy as we speak. A few observations so far.

    Likes:
    The LCD display items are cleaner and easier to read
    The "beep" tone is much...
  25. Replies
    24
    Views
    17,206

    Have not tried it yet. I grabbed the RC and am...

    Have not tried it yet. I grabbed the RC and am going through the config.h file to transfer my settings and get a feel for whats new or different.
Results 1 to 25 of 68
Page 1 of 3 1 2 3