Close
Flash Forge Guider



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    253

    It could also mean the the Stepper current...

    It could also mean the the Stepper current setting V-Ref is incorrect.
  2. Replies
    4
    Views
    253

    I would say that the bearings are binding and...

    I would say that the bearings are binding and need to be cleaned of the packing grease and then lubricated with a good oil.

    There are many oils that can be used though many you may already have in...
  3. The first layer is your most important layer. ...

    The first layer is your most important layer.

    I believe you are retracting to far try 4.5mm with a Z-Hop of .075 reduce fan min to 40 and fan max to 60.
    ...
  4. In Cura Select Preferences Click In Preferences...

    In Cura Select Preferences Click
    In Preferences select Settings Click

    Type Speed in the Dialog box

    12798

    Put A check in Support Speed boxes that apply, This will allow you to view and...
  5. Replies
    29
    Views
    1,596

    You have a Rep Rap Smart Discount Controller ...

    You have a Rep Rap Smart Discount Controller
    And you want to upgrade it to the Rep Rap Discount Full Graphics Smart Controller


    You would comment out the Rep Rap Smart Discount Controller and...
  6. Replies
    29
    Views
    1,596

    Sorry all I received was this 12783

    Sorry all I received was this

    12783
  7. This first layer is always the hardest to...

    This first layer is always the hardest to achieve. After the doing many 3D Prints you will get better.
    Though this is not something that can be set to a number, it is part learning process of 3D...
  8. Replies
    29
    Views
    1,596

    For some reason we are not communicating. ...

    For some reason we are not communicating.

    BL-Touch needs to be enabled in the Marlin Firmware you posted, You tell me it is working but when I look in the Firmware you posted it is still disabled....
  9. In the posted Image your model looks good I...

    In the posted Image your model looks good

    I use A Raspberry Pi running OctoPrint - with a OctoLapse plugin to get this kind of effect.

    PI3 SD Card Holder
    https://youtu.be/yDIp0vO5w14

    7mm...
  10. Replies
    29
    Views
    1,596

    Every version of marlin 1.1.x - 2.0.x has these...

    Every version of marlin 1.1.x - 2.0.x has these options. You just need to enable them.


    //#define BLTOUCH
    #if ENABLED(BLTOUCH)
    //#define BLTOUCH_DELAY 375 // (ms) Enable and increase if...
  11. Replies
    1
    Views
    252

    How to activate Start-up, Student or Educational...

    How to activate Start-up, Student or Educational licensing for Fusion 360

    https://www.autodesk.com/products/fusion-360/free-trial
  12. Replies
    29
    Views
    1,596

    A 3D touch is essentially a clone of the early BL...

    A 3D touch is essentially a clone of the early BL touch models.

    https://ivortheterrible.wordpress.com/2017/10/05/bed-probes-3d-touch-vs-bl-touch/
  13. Replies
    3
    Views
    189

    I do not remember when I have seen a electrical...

    I do not remember when I have seen a electrical problem that causes board to malfunction when it is turned off
    If the LCD boots then try the restore Factory

    Send M502 Restore firmware Defaults...
  14. Replies
    3
    Views
    189

    Trouble shooting! well Start by unplugging all...

    Trouble shooting! well Start by unplugging all the connectors and re-plugging them in, it could just be a oxidized connection.
  15. I do not have an Ender3. It appear that you...

    I do not have an Ender3.

    It appear that you are having major problems with the Z-Axis movement.
    One layer is too thin the next is too thick or missing as though the Z-Axis is being stuck then...
  16. Replies
    15
    Views
    993

    Though I do not have a garage, moved my 3D...

    Though I do not have a garage, moved my 3D Printers into a Work Shop area of the home basement area.
    If you have a basement you know that once smells get in here is almost no way of getting the...
  17. Replies
    5
    Views
    328

    Mastering Cura...

    Mastering Cura and 2019 Cura Tutorial here are a couple good places to start your learning experience.
  18. Replies
    2
    Views
    326

    https://www.youtube.com/watch?v=-iubywKkNEE

    https://www.youtube.com/watch?v=-iubywKkNEE
  19. Replies
    34
    Views
    1,456

    There are two way to change the direction of a...

    There are two way to change the direction of a Stepper motor.
    One - Change in the firmware "#define INVERT_Y_DIR false \\to true "
    Two - Rewire to stepper motor to change direction. If this is done...
  20. Replies
    34
    Views
    1,456

    Simply Change the Direction of the stepper. //...

    Simply Change the Direction of the stepper.

    // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
    #define INVERT_X_DIR false
    #define...
  21. Replies
    34
    Views
    1,456

    Using a terminal to control the 3D Printer Send...

    Using a terminal to control the 3D Printer Send "M119 - Endstop States "

    Then manually press the end-stops to see if all work.
    Then for the Proximity sensor you could use a spatula and tap the...
  22. Replies
    34
    Views
    1,456

    Have you tried to raise and lower the Z-Axis.

    Have you tried to raise and lower the Z-Axis.
  23. Replies
    5
    Views
    328

    The first layer is always the hardest to lay for...

    The first layer is always the hardest to lay for beginners. Because the first layer is the most critical.
    Post an image to Google Drive get a shareable link and post it here.

    Will be more the...
  24. Replies
    2
    Views
    222

    I cannot see the Image, So I am posting a...

    I cannot see the Image,

    So I am posting a image does it look like this.

    12754

    The model of the Fish Key chain is suppose to be solid, but because I have 1.75mm filament and sliced if for...
  25. Replies
    34
    Views
    1,456

    In the video it appears that your 3D Printer is...

    In the video it appears that your 3D Printer is having a hard time finding the end-stop switch.

    I also did not see the Z-Axis travel up or down to find the bed.

    First you should test the Z-Axis...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4