Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 56 minute(s) ago.

  1. This is nearly exactly what happened to my 3D...

    This is nearly exactly what happened to my 3D Prints though the clog was because of a throat with a PTFE liner slid into to nozzle Note the nozzle in the Image on right. you will see the PTFE tubing...
  2. Replies
    1
    Views
    370

    Post slicer setting, slicer an version

    Post slicer setting, slicer an version
  3. Replies
    2
    Views
    522

    I would also set the starting position to random....

    I would also set the starting position to random.

    16438
  4. Replies
    2
    Views
    303

    This could be simple as adjustment of retraction...

    This could be simple as adjustment of retraction on Z-Hop
  5. Replies
    0
    Views
    455

    3D Print Boards

    We are a new 3D print forum looking for good 3D Printer users become a member and take a look around, or just read as a quest.
  6. Please Post image from top downward

    Please Post image from top downward
  7. Replies
    17
    Views
    1,716

    PrusaSlicer 2.3.0 has downloadable profiles one...

    PrusaSlicer 2.3.0 has downloadable profiles one is a Ender 5

    Click Configuration Tab > Select Configuration Wizard > Select Other Vendors and the Creality check box
    Then select Creality FFF and...
  8. Replies
    17
    Views
    1,716

    Was looking for this could not find so did not...

    Was looking for this could not find so did not post previously

    16351

    While 3D Printing this Laptop Stand at .28mm layer height i find that the area shaded in green has a texture as that of...
  9. Replies
    17
    Views
    1,716

    Everyone has different opinions on this subject,...

    Everyone has different opinions on this subject, I have never tried Simpily3d simply because it does not have a 30 day trial or reduced functionality test program.
    Plus the initial cost is out of my...
  10. Replies
    17
    Views
    1,716

    I started using Cura though wanting better...

    I started using Cura though wanting better quality I started using PrusaSlicer 2.3.0.

    This sweet slicer that has Slic3r roots will stand above most Free Slicers and will even put some expensive...
  11. Did you download Ender 5 plus using. Select...

    Did you download Ender 5 plus using.
    Select Ender 5 Plus 3D Printer
    Click Configuration > Click Configuration Wizard ...
    Click Other Vendors Check the box Creality select Creality Ender-5 Plus to...
  12. Looks to me like you are printing the infill with...

    Looks to me like you are printing the infill with a percentage. this could be normal.
    To correct choose infill as solid or at least above 75%.
  13. Replies
    5
    Views
    943

    It seem like I am always forgetting this one

    It seem like I am always forgetting this one
  14. Replies
    1
    Views
    334

    My first to Prints with PLA I set the temp from...

    My first to Prints with PLA I set the temp from 192-196C.

    After replacing hot-end heater and thermister. Now 3D Print from 200-208C using the same PLA.
  15. Replies
    5
    Views
    943

    This is called layer shifting. It is caused by...

    This is called layer shifting.

    It is caused by a few mechanical adjustments or sticky grease on your smooth rods.
    XY axis belts too loose or too tight, V-Ref current incorrectly adjusted. Bad...
  16. Replies
    4
    Views
    651

    It has been a while since using Cura mostly use...

    It has been a while since using Cura mostly use PrusaSlicer 2.3.0 now.

    Looked In Cura 4.8.0 and it is called Infill Overlap Percentage and Infill Overlap
  17. Replies
    4
    Views
    567

    It could be that the smaller model just needs to...

    It could be that the smaller model just needs to be printed slower on your 3D Printer.

    However I doubled the set print speed on my 3D Printer an dropped the nozzle temp to 208C
  18. Replies
    4
    Views
    651

    What is you infill percentage set to. This...

    What is you infill percentage set to.


    This looks vaguely familiar.
    Set your perimeter "vertical shells" to 2 or 3 walls printing perimeter first followed by printing infill with overlay to .025
  19. Replies
    4
    Views
    567

    I printed CE3PRO_cableChain_link_v3.gcode...

    I printed CE3PRO_cableChain_link_v3.gcode and there is nothing wrong with your sliced G-code.
    Therefore it must be have something to do with filament extrusion, clogged extruder, stepper missteps or...
  20. I built an enclosure with a single sheet if...

    I built an enclosure with a single sheet if plywood it has been working for 4 years.
    The cost was the price of one sheet of plywood and some wood glue a few nails a couple of plastic sheets for...
  21. Replies
    2
    Views
    543

    Do you have more information. Post STL of Flag,...

    Do you have more information.
    Post STL of Flag, post your Cura settings ect...
  22. Replacing the Fans Power Mosfet is a simple...

    Replacing the Fans Power Mosfet is a simple process an only requires unsoldering 3 terminals then re-solder.
  23. I would test the Power Supply by disconnecting...

    I would test the Power Supply by disconnecting the Supply leads from the 3D Printer an measure the voltage.

    Reconnect and measure the voltage at the Power Supply and the controller if there is a...
  24. Replies
    2
    Views
    577

    Your posted image suggests under extrusion,...

    Your posted image suggests under extrusion, Stepper slippage clogged nozzle ect...

    Post your slicers model settings
  25. Replies
    12
    Views
    2,135

    Using my slicer I can select a Seam Position of...

    Using my slicer I can select a Seam Position of Random then the Start Seam becomes invisible into this random starting position.
Results 1 to 25 of 496
Page 1 of 20 1 2 3 4