Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    595

    Never had a glass bed will leave for someone who...

    Never had a glass bed will leave for someone who has, for your answer.
  2. I would never attend an ex's wedding. Sorry to...

    I would never attend an ex's wedding. Sorry to hear you will.
  3. Replies
    15
    Views
    595

    License if forever for Hobbyist, I have been...

    License if forever for Hobbyist, I have been using it for 3 years now.
    Though have only made a dozen or so models.
  4. Replies
    15
    Views
    595

    I too use ThinkerCad and Cura Slicers. I also...

    I too use ThinkerCad and Cura Slicers.
    I also have the Personal use version of Fusion 360

    Now this program has a steep learning curve I was told.
    Though I watched a few You-Tube videos and...
  5. Replies
    15
    Views
    595

    It appears from photo that the bed is higher in...

    It appears from photo that the bed is higher in front. Re-leveling bed could fix.
    You could raise the print to start about 0.1mm higher and this will most likely correct the problem.
  6. Replies
    4
    Views
    273

    Three years ago I purchased my first 3D Printer,...

    Three years ago I purchased my first 3D Printer, it was a used system that the original owner could not get to work.

    When I received the 3D Printer it did not come with the Assembly instructions...
  7. Replies
    15
    Views
    595

    1. I installed a switch so merely turn my 3D...

    1. I installed a switch so merely turn my 3D Printer off when finished 3D Printing.

    2. Cleaning your bed after print is correct, I also clean my bed with alcohol before 3D Printing to remove the...
  8. Replies
    4
    Views
    273

    The Ender3 v2 should have come flashed with your...

    The Ender3 v2 should have come flashed with your firmware.

    This would lead me to believe that the Z-Axis is not moving smoothly, this in turn would lead to missed steps on the Z-Axis.
    I would...
  9. A quick search I see that the Zonestar Z6FB has a...

    A quick search I see that the Zonestar Z6FB has a choice of Marlin or Repetier,

    Though reading the "How to Correct the origin position.PDF" I believe you are setup for Repetier firmware.
    ...
  10. Replies
    5
    Views
    475

    Lay shift can be caused by any mechanical part...

    Lay shift can be caused by any mechanical part getting stuck for a short period of time.
    This includes lead screws, belts, bearings and stepper motors.
    All these mechanical parts can bind causing a...
  11. Replies
    5
    Views
    1,608

    In cases where the filament sticks too securely...

    In cases where the filament sticks too securely raise the nozzle slightly so as to have less adhesion.
  12. Photo 14701 I had the Camera against the...

    Photo
    14701

    I had the Camera against the wall,
    The Enclosure is a Full 4 x 8 foot sheet of plywood with two Clear 24w X 18h inch Plastic sheet hanging from a 4 foot hinge.
    Leaving a 24 X 6...
  13. Have setup PrusaSlicer - Slic3r...

    Have setup PrusaSlicer - Slic3r quite some time ago using Cura Settings below, well today I am printing the first Model.

    Decided to test PrusaSlicer today as nothing else to do. My workload has...
  14. Thank You much. Though I have already tried many...

    Thank You much.
    Though I have already tried many slicers, including Prusa slicer.

    14675
  15. I have a plastic front which cover 90% of the...

    I have a plastic front which cover 90% of the front leaving about 10% of the bottom front that is used to draw air.
    In the back of my enclosure I have a bathroom fan that is used to suck the smelly...
  16. My 3D Printer enclosure has a light dimmer...

    My 3D Printer enclosure has a light dimmer control and a bathroom fan. I have a vent hole that the fan draws air from.

    When printing any model with air flow can ruin prints, I use only enough air...
  17. I understand though before I spend $150 dollars...

    I understand though before I spend $150 dollars would have to test any program purchased with a trial run. And this is not provided by simplify3d.
    curious aardvark can I connect to my 3D Printers...
  18. Replies
    5
    Views
    547

    If you looked at my 1st post you would see that I...

    If you looked at my 1st post you would see that I have a filament run-out sensor, on both of my 3D Printers.
    it was a simple project and was easily added to the controller and firmware.

    Final...
  19. Still today I use the older Cura 15.04.6 or if...

    Still today I use the older Cura 15.04.6 or if you like a Creality Slicer which is the a clone of Cura 15.04.6.

    Below are my settings


    14651

    14652

    14653
  20. Replies
    5
    Views
    547

    I have had filament break before I made my single...

    I have had filament break before I made my single sheet of plywood dual 3D Printer case.

    14635

    I can not say that the filament inside my enclosure has not broke,
    though it has reduced...
  21. This is probably correct You have a T8-8 which is...

    This is probably correct You have a T8-8 which is a 2mm pitch 4 start lead screw.
    This is different from a T8-2 which is a 2mm pitch single start lead screw.

    The difference is the if you rotate...
  22. I have posted about this before. T8-8 Lead-screw...

    I have posted about this before.
    T8-8 Lead-screw Drop with Gravity

    https://youtu.be/yFHEIdUf2Lw

    Image of three lead screws T8-8mm pitch (4 start), T8-2m pitch (single start), and All thread...
  23. Here is a couple ways that may help. When the...

    Here is a couple ways that may help.

    When the printer is just sitting if the steppers are disabled then the chance is higher that the Z-Axis will drop.
    I suggest that you should home your printer...
  24. I purchased a BigTree RepRap smart discount...

    I purchased a BigTree RepRap smart discount controller and had to make my own cables.

    I have posted about this before though will give a quick rundown again.

    Note that on this BigTree RepRap...
  25. Look here ...

    Look here

    https://3dprintboard.com/showthread.php?45232-Help-ID-board-Max-Micron-(Prusa-Mendel-I3-clone)
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4