Close



Dig deeper, search our News website




Search:

Type: Posts; User: kd7eir

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    17
    Views
    6,281

    An excellent post with critical safety...

    An excellent post with critical safety recommendations.
  2. Replies
    17
    Views
    6,281

    A photo and the specs/model number of the relay...

    A photo and the specs/model number of the relay that you are using would be very helpful in figuring this out.
  3. Replies
    9
    Views
    4,217

    NEVER did I say that an inductive probe was the...

    NEVER did I say that an inductive probe was the only way to accomplish ABL, so stop putting words in my mouth. YOU stated that "a bed leveling probe is totally useless to fix the problem." I hate to...
  4. Replies
    9
    Views
    4,217

    ABL is a PROVEN TEHCNOLOGY. Just because YOU...

    ABL is a PROVEN TEHCNOLOGY. Just because YOU don't like does not change that FACT.

    Empirical evidence has proven that ABL works, and works very well. The anecdotes of naysayers are incapable of...
  5. Replies
    9
    Views
    4,217

    Because a 3D printer is a moving machine, and...

    Because a 3D printer is a moving machine, and moving machines are incapable of maintaining perfect alignment due to the laws of physics.
  6. Replies
    9
    Views
    4,217

    Inductive sensors work just fine with MakerFarm...

    Inductive sensors work just fine with MakerFarm printers. This is the one that I use and it works fine through 3mm borosilicate glass. It has a sensing distance of 8mm, which works out to about 3.2mm...
  7. Thread: Z offset issue

    by kd7eir
    Replies
    1
    Views
    1,470

    Z offset issue

    RESOLVED - I reloaded the firmware and it's back to normal now.

    I changed the RAMPS board on my printer.

    Z offset was set at 1.25 previously. After changing the RAMPS board, now it's decided...
  8. Replies
    13
    Views
    5,139

    I'm using ESun PLA Pro. The hobbed bolt is nice...

    I'm using ESun PLA Pro. The hobbed bolt is nice and clean. Nozzle has been checked, and even replaced with a spare nozzle with no change.
  9. Replies
    13
    Views
    5,139

    Yes. That's why I'm so baffled - I cannot think...

    Yes. That's why I'm so baffled - I cannot think of or see anything that could be causing it.

    Belts are tight, all the nuts are tight, bed is clean, rods are straight, etc
  10. Replies
    13
    Views
    5,139

    Bed has been leveled manually, and then I use ABL...

    Bed has been leveled manually, and then I use ABL before each print. No clicking from the extruder. Same filament as always.
  11. Replies
    13
    Views
    5,139

    Strange print behavior

    Any idea what would be causing this?

    9808

    Nothing has changed in my printing process. The same gaps have appeared in several different files that I have tried printing.
  12. Replies
    13
    Views
    6,265

    When my bed temp is set for 80°C, the surface...

    When my bed temp is set for 80°C, the surface temperature through the 5/16" borosilicate glass is 57.3 °C

    I've never cared about the temperature of the surface - I know that setting my bed for...
  13. He is bypassing the FET on the RAMPS board with...

    He is bypassing the FET on the RAMPS board with the MOSFET he ordered. The silicone heating pad is 200 watts, and the MOSFET he ordered is rated at 25 amps, so that is fine. The NTC3950 thermistor...
  14. Did you compile and uploaded the firmware after...

    Did you compile and uploaded the firmware after changing the servo endpoints?

    Try testing with this, making sure the probe ends up where you expect

    M401 - deploys the probe
    M402 - retracts the...
  15. Replies
    3
    Views
    2,223

    Here's the link http://www.kd7eir.net/Marlin.zip

    Here's the link http://www.kd7eir.net/Marlin.zip
  16. Replies
    3
    Views
    2,223

    I can zip mine up and give you a link to it in...

    I can zip mine up and give you a link to it in the morning. I have the itty bitty belted extruder and hexagon .4 3mm hot end in use right now, so you may need to edit it a bit.
  17. Replies
    11
    Views
    3,373

    Glad that I could help.

    Glad that I could help.
  18. Replies
    1
    Views
    1,597

    10" heated bed source

    Any recommendations on a US source for a 10" x 10" heated bed, besides MakerFarm? Silicone or PCB.

    The bed that came with my 10" I3v has several dead zones after a couple years of use, and I'm not...
  19. Replies
    11
    Views
    3,373

    In the configuration.h file, you will find: ...

    In the configuration.h file, you will find:

    //#define PROBE_SERVO_DEACTIVATION_DELAY 300

    I highly suggest you uncomment this line so that it detaches the servo after movement. You have probably...
  20. Replies
    11
    Views
    4,125

    That makes sense - under load the loose set screw...

    That makes sense - under load the loose set screw could allow the pulley to slip across the flat, but without the belt in place and under no load, the pulley would stay in place.
  21. Replies
    11
    Views
    4,125

    You can physically see a bump under the belt at...

    You can physically see a bump under the belt at the pulley when the skip happens. A video of the motor performing the same movements, from the same viewpoint, just without the belt in place would be...
  22. Thread: Show your MODS

    by kd7eir
    Replies
    187
    Views
    128,758

    Sticky: I guess that's possible

    I guess that's possible
  23. Replies
    11
    Views
    3,373

    Follow the section "Roughly Calibrate the Z...

    Follow the section "Roughly Calibrate the Z Offset" here - http://clough42.com/instructions/marlin-firmware-setup/
  24. Thread: Show your MODS

    by kd7eir
    Replies
    187
    Views
    128,758

    Sticky: This time elapsed between the first two prints...

    This time elapsed between the first two prints that succeed and the following prints that fail is less than one hour - moisture is not the problem.
  25. Replies
    11
    Views
    4,125

    If it doesn't do it with the belt attached then...

    If it doesn't do it with the belt attached then carefully examine the pulley and belt, and replace whichever one has the defect.
Results 1 to 25 of 137
Page 1 of 6 1 2 3 4