Close



Dig deeper, search our News website




Search:

Type: Posts; User: CTC-USA

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    24,219

    We have found Makerware 3.7 made changes to the...

    We have found Makerware 3.7 made changes to the software. For best results, use Makerware 3.6!
  2. Replies
    2
    Views
    2,507

    We have seen good results from using an spool...

    We have seen good results from using an spool holder, next to the printer. Filament spooling from OVER the spool into the printer.

    Try placing the spool holder on the table next to the printer on...
  3. Try using 3.6 Makerware. Use an higher...

    Try using 3.6 Makerware.

    Use an higher infill, something like 50%+.
  4. Please contact our service department for free...

    Please contact our service department for free replacement of the printer or motherboard if you have USB+.

    Kind Regards,
  5. https://www.youtube.com/watch?v=yJaN7iYt9H4 ...

    https://www.youtube.com/watch?v=yJaN7iYt9H4

    http://ctc3d-usa.com/index.html
  6. Formaker 3-in-1 Multifunction Manufacturing Machine

    Some quick shots of our newest project.

    Initial Pricing is $999 for the Whole Machine.

    Functions
    -CNC Router
    -Laser Cutter
    -3D Printer

    Features
  7. Replies
    3
    Views
    2,604

    All our printers shipped with at least 7.2/7.3...

    All our printers shipped with at least 7.2/7.3 firmware. There is no major improvements to the firmware after that.

    You will be fine with your version.
  8. Replies
    3
    Views
    2,604

    Hi, I know 16Gb cards work fine, however I...

    Hi,

    I know 16Gb cards work fine, however I think the Makerbot firmware higher than 7.4 removes SD compatibility.
  9. I only know of them as a kit from: Here...

    I only know of them as a kit from:

    Here

    You have 3mm inlet to the nozzle, and 3mm PTFE style.
  10. http://3dprintboard.com/attachment.php?attachmenti...

    http://3dprintboard.com/attachment.php?attachmentid=5432&stc=1

    This is a nozzle assembly.

    Nozzle removal is : Left turn removes, Right turn tightens.
    Same for cooling tower, the long piece....
  11. Your welcome. POWER OFF - Unplugged Loosen...

    Your welcome.

    POWER OFF - Unplugged

    Loosen the hex key for the said hot-end. Then lower the bed all the way.

    Disconnect the connections for the heater cartridge, etc.

    Your...
  12. Just the parts alone cost about $375. No...

    Just the parts alone cost about $375.

    No housing, no frame, no extras.

    Biggies being the Stepper Motors/Drivers/Motherboard/Rods/Power Supply.
  13. Replies
    4
    Views
    3,446

    You want the entire nozzle assembly as close to...

    You want the entire nozzle assembly as close to the extruder as possible. With the fans off, you'll note that you can raise the "cooling tower" all the way to the plastic extruder housing. This will...
  14. You will need to remove the cooling tube and the...

    You will need to remove the cooling tube and the nozzle. Disconnect the connections to the aluminum block.

    Measure the needed PTFE, then cut with sharp knife.

    Insert the PTFE into the nozzle,...
  15. Replies
    6
    Views
    24,219

    CTC Print Settings for Beginners (General)

    We used Makerware with only the Standard and High presets. Makerware Firmware 7.5.

    The printer is an CTC Bizer/Replicator, with Matterhackers Pro ABS/Pro PLA

    ABS:


    110C Build plate
    ...
  16. Thread: CTC on 3D Hubs

    by CTC-USA
    Replies
    0
    Views
    2,135

    CTC on 3D Hubs

    Here's a link to our community on 3D Hubs.

    We have been able to as of now, be the #3 printer in print quality!

    3DHubs
  17. Replies
    2
    Views
    6,391

    What would you like to know? It is a fantastic...

    What would you like to know?

    It is a fantastic printer that battles with the Makerbot Replicator 2.

    Our price is much much less. Many of our customers use these machines 24/7 as you can buy 4...
  18. Replies
    16
    Views
    12,179

    In case you guys were wondering about Bizer 3...

    In case you guys were wondering about Bizer 3 build size:

    Building Size : 225 * 145 * 150mm

    Bizer 3 Info
  19. Replies
    16
    Views
    12,179

    We are using our own electronic PCB for the...

    We are using our own electronic PCB for the motherboard. Not a clone from another maker. Its available in ENG and JAP
  20. Replies
    16
    Views
    12,179

    Yes others are free to form their own opinion. ...

    Yes others are free to form their own opinion.

    We never went to kickstarter, nor complained of others using our innovations.

    I do not believe Form1 is a patented tech, therefore others can...
  21. Replies
    16
    Views
    12,179

    If that was true, then Form1 would have an clear...

    If that was true, then Form1 would have an clear cut case wouldn't they?

    There is more to the story I assure you.
  22. Replies
    16
    Views
    12,179

    I was inferring all 3D technologies originated...

    I was inferring all 3D technologies originated with another product.

    Kinda like car engines. All manufacturers make their own however they all have pistons, rods, and crankshafts..... Even the...
  23. Very Cool.

    Very Cool.
  24. Replies
    7
    Views
    6,691

    We have found the best lube for roller bearings...

    We have found the best lube for roller bearings and precision rods is Remington Firearm Lube.

    We don't even notice the printers running they are so quiet.

    With Lithium Spray of any kind it...
  25. Replies
    16
    Views
    12,179

    http://makezine.com/2012/11/21/3d-systems-suing-fo...

    http://makezine.com/2012/11/21/3d-systems-suing-formlabs-and-kickstarter-for-patent-infringement/

    I will not speculate.

    The 3D Printer market is littered with $3500 hardware that is worth $800...
Results 1 to 25 of 29
Page 1 of 2 1 2