Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    150

    This is most probability because unless you are...

    This is most probability because unless you are using the Octolapse plugin you do not need more power.
    Unless you are planning to use more than one web camera or Octolapse then go with the Pi 4.
  2. Replies
    3
    Views
    150

    The software OctoPrint will work on the Pi4 since...

    The software OctoPrint will work on the Pi4 since it runs everywhere Python 2.7 runs.

    RPi image OctoPi 0.16 or earlier will not work since it doesn't yet support the new hardware.

    Octopi...
  3. 3d printing threads tolerance is something that...

    3d printing threads tolerance is something that requires a Guide.

    I would suggest using the Many google guides for 3D Printing Threads

    Here is one such tutorial
  4. Replies
    2
    Views
    182

    I would leave bed at 50C and adjust the nozzle up...

    I would leave bed at 50C and adjust the nozzle up to about 200C.

    My 3D Printer print PLA best at 202C, though had printed for a long time at 196C with really good results.
  5. Replies
    8
    Views
    1,019

    I setup my 3D Print it starts at the Bed then...

    I setup my 3D Print it starts at the Bed then Raises to whatever Layer Height is set and starts the Print.

    Do not understand the purpose of all the G1 Code lines
    G1 Z15.0 F{travel_speed} ;move...
  6. Private message me, could possibly print this in...

    Private message me, could possibly print this in 2 or 3 pieces with a type of tongue and groove that could be epoxied together to form a single piece.
    Top and Bottom with a single piece cape.
  7. Replies
    8
    Views
    1,019

    Hi; Took a look at your files, they look ok. ...

    Hi;

    Took a look at your files, they look ok.

    Let me get some more information, What is your Z-Axis lead Screw.
    Sample Code from my own Z-Axis below

    // Typical stepper motors have 200 steps...
  8. Replies
    3
    Views
    276

    I Reduced it using TinkerCAD to fit on my bed

    I Reduced it using TinkerCAD to fit on my bed
  9. It appear that it thinks it is already at a...

    It appear that it thinks it is already at a Z-Axis of zero, this could be why it will not travel down.

    Check to see is a M119 says that the BL-Touch is already sensing that you are at Zero.
  10. Replies
    4
    Views
    841

    YES!!! I had printed only a few items that I...

    YES!!!

    I had printed only a few items that I wanted and have already saved the price of both my 3D Printers.
  11. There are so many things that can affect the...

    There are so many things that can affect the filament and failed 3D Prints, though it is highly possible.

    Sorry forgot to post.

    Search google for " Bad Filament " it will list many sites.
  12. I too have had this problem, not so much with PLA...

    I too have had this problem, not so much with PLA though when printing ABS the warping was horrendous.

    I found the easiest way to print without warping was to print inside an enclosure.
    I build...
  13. You are layer shifting, and as you have stated it...

    You are layer shifting, and as you have stated it is shifting the Y axis only.

    Here are a few things that can cause this layer shifting.
    Smooth rods are not parallel and binding.
    Smooth rod...
  14. Replies
    4
    Views
    1,726

    This is why the quality of work in the world is...

    This is why the quality of work in the world is going downhill and nothing works correctly anymore.

    If a magnetic pulse was to hit the world today an wipe out everything the generations that come...
  15. In Cura 14.04.6 you select supports shown in the...

    In Cura 14.04.6 you select supports shown in the Photo below

    13812
  16. I would print with Supports, this will only take...

    I would print with Supports, this will only take 13 minutes to print.
  17. Replies
    4
    Views
    1,726

    Anyone who allows someone else do there school...

    Anyone who allows someone else do there school work is only hurting themselves.
  18. Replies
    2
    Views
    311

    Yes Filament can cost from $10 a roll up...

    Yes



    Filament can cost from $10 a roll up to $335 a roll for Carbon fiber. You may never need this roll of carbon Fiber filament.
  19. Good Catch!!!

    Good Catch!!!
  20. Replies
    1
    Views
    354

    Hello Awesome I liked the puzzle boxes,...

    Hello Awesome

    I liked the puzzle boxes, thanks for posting the links.

    Keep it up
  21. I am sorry that you took offense, As I too took...

    I am sorry that you took offense, As I too took offense at your post.

    It is not our fault that $200 is all we could afford. My Amateur Radio's and 3D Printers are my most valuable property.
  22. Not sure I agree - for the price of your 3D...

    Not sure I agree - for the price of your 3D Printer I could purchase ten Hictop 3D Printers.

    13743

    Hictop has a larger print area 220 x 270 x 200mm.

    Have already proven I can print ABS one...
  23. Replies
    6
    Views
    892

    Post a picture, I have seen many 3D Printers...

    Post a picture,

    I have seen many 3D Printers with 300x300 heated beds supported by two linear rails using dual lead screws.
    So the answer it can be done.
  24. Replies
    0
    Views
    702

    MPK.V1 Controller

    When installing Firmware on Stock Controller SD works on the 2004 LCD {RepRap Discount Smart Controller}, When installing Firmware on new controller the Onboard SD Card Reader works and disables...
  25. Replies
    1
    Views
    457

    When flashing new firmware you need to send code...

    When flashing new firmware you need to send code to read the firmware and store the firmware configuration into memory.

    To do this send
    M502 - Factory Reset
    // If you need a different Z-Offset...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4