Close



Dig deeper, search our News website




Search:

Type: Posts; User: curious aardvark

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. corexy is faster, more precise and just better...

    corexy is faster, more precise and just better all round.
  2. Replies
    1
    Views
    162

    I will admit to knowing almost nopthing about...

    I will admit to knowing almost nopthing about firmware setup - but looking at the board: Atmega2560 and Atmega32u2
    could it be you need to use the 32bit atmega32u2 rather than the 8bit atmega 2560...
  3. have ago with openscad - it would probably have...

    have ago with openscad - it would probably have been a lot quicker to just model that part from scratch, than buggering about fixing a duff model :-)
  4. Replies
    6
    Views
    441

    lol - I owe simplify3d an apoloogy. Just started...

    lol - I owe simplify3d an apoloogy. Just started the 0.3mm box off. And it turns out that the 3 hours and 9 minutes it took to print at 0.16 was EXACTLY the time s3d said it would take.
    I just read...
  5. Replies
    8
    Views
    1,482

    obviously not :-) I can usually get away with...

    obviously not :-)
    I can usually get away with printing and of the hybrid pla's on a cold bed. Not found any with either added materials or made flexible that actually need a heated bed.

    I did...
  6. Replies
    6
    Views
    441

    well still takes 3 hours. simplify3d 4.1 - is...

    well still takes 3 hours.
    simplify3d 4.1 - is almost exactly an hour out in it's stimation.
    Which i find hard to understand as it generates every command and knows the speed of the printhead and...
  7. there have been a coupleof supposed addons for...

    there have been a coupleof supposed addons for phones that either never get rolled out on more than one model or just never get the software support they need.

    A few years back the next big thing...
  8. Replies
    8
    Views
    1,482

    As I've never had ANY pla warp or melt in sun -...

    As I've never had ANY pla warp or melt in sun - so I'd have to say no.

    do you all live in death valley or what ?
  9. https://www.sciencedirect.com/science/article/pii/...

    https://www.sciencedirect.com/science/article/pii/S2468067217300822

    have a read through that as well. :-)
  10. get a decent printer and make your own paste...

    get a decent printer and make your own paste extruder
    This one is designed to fit a prusa - also a good machine to get.
    lol you can tll it's an old video by the stepper motor sounds :-) My old...
  11. Replies
    36
    Views
    2,614

    lol - I love the little 3.5 screen on the...

    lol - I love the little 3.5 screen on the sapphire.
    But then I've never had a touchscreen on a 3d printer before :-)
    plenty big enough for me. It's not like I'm watching youtube videos on it :-)
    ...
  12. Replies
    8
    Views
    532

    you tell it what the thermnistor is. should...

    you tell it what the thermnistor is.

    should be able to do it with the original firmware if you can update the configuration file.
    what firmware is it ?

    It's just something I've noticed in...
  13. grey picture on a grey background - is not very...

    grey picture on a grey background - is not very clear :-)

    What did you model it in ?

    And how thick were the 'walls' for the protuberances - at least i think they are protuberances. (grey on...
  14. well I suspect that in 2021 there will be abetter...

    well I suspect that in 2021 there will be abetter time to get into scanning from a phone.
    Also 2022 2023 2024, etc.
    At the moment you need a smartphone that costs upwards of $700

    Some of us...
  15. Replies
    2
    Views
    225

    that's just a mess. Also would never print...

    that's just a mess.
    Also would never print without supports in the centre.
    oops, turn it upside down and if it were solid it should print without supports _ I think.
    It looks like the top part...
  16. Replies
    6
    Views
    441

    even did both parts at the same time for each...

    even did both parts at the same time for each box.
    15404
    15405
    15406

    they were all printed on my sapphire pro corexy at 0.16 layer height and 150mms speed.
    Both halves of a box were printed...
  17. Replies
    8
    Views
    532

    most firmwares already have the various...

    most firmwares already have the various thermistor types included - you just have to tell it which one you have.
    Or at least all the firmware config files I've seen have this option.
  18. Replies
    6
    Views
    441

    cheers dude :-) printed three of the old style...

    cheers dude :-)

    printed three of the old style - all at 150mm/s and 50mm height :-)
    I did have to adjust internal walls/dimensions by -0.1mm to get smoothly working boxes with no post processing....
  19. Replies
    8
    Views
    532

    also they are all rated for different max running...

    also they are all rated for different max running temps.
    How does a new hotend NOT come with a compatible thermistor ?

    Surely a heat cartridge and thermistor are two things a hotend always...
  20. News I'm not on instagram :-)

    I'm not on instagram :-)
  21. Replies
    36
    Views
    2,614

    well for a timker toy that takes up almost no...

    well for a timker toy that takes up almost no deskspace:...
  22. Are the cartridges chiplocked ? otherwise -...

    Are the cartridges chiplocked ?

    otherwise - why can't you drill a hole, make a bung and just refill with 3rd party resin :-)
  23. Replies
    15
    Views
    1,097

    yeah figured it was aprogrammer thing. So my...

    yeah figured it was aprogrammer thing.

    So my ongoing openscad issue - how to make inported stl's actually work in a full render.

    I used to load stls into tinkercad and export them back to my...
  24. Replies
    4
    Views
    473

    I think 'gustavo' is a bot of some description. ...

    I think 'gustavo' is a bot of some description.

    But it does look pretty cool :-)
  25. Replies
    6
    Views
    574

    0.8mm nozzle ? thenj you need it hotter. try...

    0.8mm nozzle ?
    thenj you need it hotter.
    try 210-220c
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4