Close



Dig deeper, search our News website




Search:

Type: Posts; User: scalci

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    22,300

    Thx Roxy, I will do that now. I fired up the...

    Thx Roxy, I will do that now. I fired up the printer still on RC7, and ai het a "printer haulted" error while hearing up...

    I will do the upgrade first...
  2. Replies
    3
    Views
    5,853

    Apologies for the delay... It is a Inductive...

    Apologies for the delay...

    It is a Inductive type proximity switch
  3. Replies
    14
    Views
    15,229

    Arhur wit this in mind, I also run S3D, what...

    Arhur wit this in mind, I also run S3D, what other oprions are there fr software?

    PS. I just ordered. 4xc and 5xc this week :) :)
  4. Replies
    2
    Views
    22,300

    Marlin - Enstop Setup

    Hi Everyone

    I need some help.

    I have been running Marlin (just upgraded to the latest RC :)) for a while on a RUMBA board but never setup the endstops. I bought the OPTICAL ones.

    I read a...
  5. Replies
    14
    Views
    15,229

    Hi Everyone I am currently looking to replace...

    Hi Everyone

    I am currently looking to replace my RAMPS with a Smoothieboars.

    Does anyone have any further updates on this?

    Rgs
  6. Thread: Kinects scanner

    by scalci
    Replies
    16
    Views
    13,441

    What software do you guys use?

    What software do you guys use?
  7. Replies
    67
    Views
    176,995

    Sticky: Roxy, when do you expect RC7 to goto Stable? I...

    Roxy, when do you expect RC7 to goto Stable?

    I am in RC5, but if the time is short I will rather wait for the stable,release.
  8. Replies
    12
    Views
    7,703

    Also look at Fusion360, I use it for my CNC and...

    Also look at Fusion360, I use it for my CNC and 3D printing
  9. Replies
    3
    Views
    5,853

    RUMBA / MARLIN / Proximity Sensor

    Hi Everyone

    Can anyone assist me please?

    I want to setup a proximity sensor on a RUMBA board with the MARLIN firmware.

    1. How to wire it?
    2. Changes in Firmware?
  10. Replies
    0
    Views
    2,445

    Marlin - Backlash

    Hi Everyone

    Is the a way to set backlash in Marlin?

    rgs
  11. Replies
    4
    Views
    3,934

    Hi Roxy thank you, I will start with this and...

    Hi Roxy

    thank you, I will start with this and work up.
  12. Replies
    4
    Views
    3,934

    Roxy that is what I am doing.... Is there a sweet...

    Roxy that is what I am doing.... Is there a sweet spot?

    When I went to the latest RC code I left everything at defaults except the steps... If I change one setting at a time, will It work or do...
  13. Replies
    31
    Views
    29,554

    I did the RC upgrade today :) works as the...

    I did the RC upgrade today :) works as the prevois version. Where can I read up on the changes?
  14. Replies
    4
    Views
    3,934

    RAMPS 1.4 & Marlin

    Hi Everyone

    I need some input.

    I build my printer with a RAMPS 1.4, DRV8825 drivers, Latest Marlin, Nema24 steppers and threaded rods.

    I had a huge wobble on the X&Y, so I replaced the...
  15. Replies
    3
    Views
    4,548

    Hi, I see on the web a few that had/have issues...

    Hi, I see on the web a few that had/have issues with calibrations and also quality. These were in May 2015. Was this solved in the current hardware and software?
  16. Replies
    28
    Views
    144,768

    Sticky: Is there any update to thicj sticky?

    Is there any update to thicj sticky?
  17. Replies
    31
    Views
    29,554

    I did mine but screwed somewhere up :( I am...

    I did mine but screwed somewhere up :(

    I am now going through line n line....

    Is there a way to get the current config from the Arduino?
  18. Replies
    31
    Views
    29,554

    Roxy, thank you, I will look at this now... :) my...

    Roxy, thank you, I will look at this now... :) my line in South Africa is a bit slow, so should have it soon...
  19. Replies
    31
    Views
    29,554

    Hi, Everyone what is the best way to upgrade to...

    Hi, Everyone what is the best way to upgrade to keep your configuration?
  20. Thread: RAMPS or RAMBO

    by scalci
    Replies
    14
    Views
    23,817

    Same here have not had any issues yet. What I...

    Same here have not had any issues yet.

    What I am looking at now, if I should move to another firmware version, I am using Marlin currently.
  21. Replies
    1
    Views
    2,533

    DIY 3D Printer Parts

    Hi Everyone

    I am building my own 3D printer with the RAMPS kit. Two area's I need to get done is the Hotend and extruder.

    Where can I buy these from or makes the better ones?

    Rgs
    Scalci
Results 1 to 21 of 22