Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    198

    I placed my M420 in Cura's Startup G-Code adding...

    I placed my M420 in Cura's Startup G-Code adding it to the very last line.

    M420 S1 ; Bed Leveling On
  2. Replies
    8
    Views
    432

    How much smaller is the Other heater Cartridge...

    How much smaller is the Other heater Cartridge hole than the Original cartridge.
    If there is not much difference then make the hole large enough to fit the original cartridge.
  3. Replies
    2
    Views
    143

    Many are using a silicone Sock on the hot-end...

    Many are using a silicone Sock on the hot-end heater block or Pack insulation material around the heater block this should help.
  4. Replies
    19
    Views
    3,555

    The answer is

    The answer is
  5. Replies
    1
    Views
    265

    Found on " Ultimaker Community of 3D Printing...

    Found on " Ultimaker Community of 3D Printing Experts " posted by Labern " you can change the x-y distance "
    Started to Play with the Distance X/Y (mm) found that a change from 0.7 to 0.8 was all...
  6. Replies
    1
    Views
    265

    Cura 15.04.6

    Is there a reason why Cura 15.04.6 will not generate a Support for the attached link model mask_middle_v1.stl

    https://www.thingiverse.com/thing:4242337

    I would appreciate any help in setting Up...
  7. Replies
    5
    Views
    415

    As this is a Ender3 with layer problems I would...

    As this is a Ender3 with layer problems I would guess that the XYZ axis may need adjusting.

    Layer shifting could be caused by the XY Axis not having a smooth travel path most likely the Eccentric...
  8. Replies
    5
    Views
    415

    Post the Problems you are having the forum and I...

    Post the Problems you are having the forum and I will help you get it printing.
  9. Replies
    8
    Views
    432

    Thermistor cartridge all have a specific table of...

    Thermistor cartridge all have a specific table of resistance for a given temperature change.
    If you put a different thermistor cartridge in you will need to create data table for that specific...
  10. Replies
    19
    Views
    3,555

    Posted the question on his forum " What are the...

    Posted the question on his forum " What are the yellow worms for ".
  11. Replies
    7
    Views
    882

    OK! Currently Printing Fail Proof Fidget Cubes...

    OK!
    Currently Printing Fail Proof Fidget Cubes on both systems for Halloween trick or Treats.

    Same 24v worked the 12v failed.
    This is not saying that because it is 12 or 24 volts is works or...
  12. Replies
    7
    Views
    882

    The Hinges stick on my 12v machine while they...

    The Hinges stick on my 12v machine while they work perfectly on my 24v machine.

    I can switch the filament between the two machines still the 12V printer does not like the Turtle Ear Saver

    I...
  13. Replies
    7
    Views
    882

    I have been using the T8-2 single start lead...

    I have been using the T8-2 single start lead screw now for 2 year on both my machines.

    I have recently flashed the 2.06 marlin firmware, the funny thing is that when I print "Flexi Turtle Ear...
  14. Replies
    7
    Views
    882

    When you changed the Lead screw to a T8-2 lead...

    When you changed the Lead screw to a T8-2 lead screw.

    what are your DEFAULT_AXIS_STEPS_PER_UNIT
  15. You were printing with ABS an then switched to...

    You were printing with ABS an then switched to PLA.

    Did you Purge the ABS from the hot-end by running PLA to the ABS temp and Pushing Extra ABS from the Hot-End.
  16. Please Post Images. Probable Cause -filament...

    Please Post Images.

    Probable Cause -filament adsorbed moisture.

    Solution - Using a dehydrator



    Type
    Temperature
  17. Replies
    3
    Views
    451

    As an example I have Sliced with Cura 3.6.0 Layer...

    As an example I have Sliced with Cura 3.6.0 Layer Height .32 with a .4mm nozzle PLA Printed at 202C on a 46C hotbed with print speed of 7.8^3mm per second.
    The print was done in under 4 hours if it...
  18. Replies
    3
    Views
    451

    There are many pitch lead screws, some travel 8...

    There are many pitch lead screws, some travel 8 mm with 200 steps others only move 1mm with 200 step.
    If we did not have micro-steps.

    My 3D Printer only has 16 micro-steps some have capabilities...
  19. I loaded both models with several version of Cura...

    I loaded both models with several version of Cura no errors posted.

    Your flashforge adventurer 3 has a 150mm Build area you have plenty of room.
  20. I downloaded the posted thingiverse models and...

    I downloaded the posted thingiverse models and took measurements and the pieces should fit together.

    Using PLA should allow for the printed parts to match as well.

    Do you have any more...
  21. Yes it is sometime difficult to determine the...

    Yes it is sometime difficult to determine the temperature that is best for different filaments.

    My 3D Printers print PLA at 202C this temperature was verified with a temperature probe on my...
  22. Do you have the ability to make a video post it...

    Do you have the ability to make a video post it to a share like google drive or You-Tube

    Then Post a link so we can see!!!
  23. I have read this thread and everyone has an...

    I have read this thread and everyone has an opinion, though if the Programmers never created the first program to write another program with.
    Then the coders would have nothing to write code with,...
  24. Replies
    5
    Views
    1,208

    If two things would happen they might have a...

    If two things would happen they might have a better chance of selling me Simplify 3D
    1. A demo to test the program before purchase, though the purchase price is still higher than I would pay. Have...
  25. It could also be Stepper drivers V-Ref is too...

    It could also be Stepper drivers V-Ref is too high causing the drivers to over heat, this intern allows the extruder to misstep and ultimately clog.

    My 3D Printers have a factory V-Ref of 0.800...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4