Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. A quick search I see that the Zonestar Z6FB has a...

    A quick search I see that the Zonestar Z6FB has a choice of Marlin or Repetier,

    Though reading the "How to Correct the origin position.PDF" I believe you are setup for Repetier firmware.
    ...
  2. Replies
    5
    Views
    370

    Lay shift can be caused by any mechanical part...

    Lay shift can be caused by any mechanical part getting stuck for a short period of time.
    This includes lead screws, belts, bearings and stepper motors.
    All these mechanical parts can bind causing a...
  3. Replies
    5
    Views
    1,569

    In cases where the filament sticks too securely...

    In cases where the filament sticks too securely raise the nozzle slightly so as to have less adhesion.
  4. Photo 14701 I had the Camera against the...

    Photo
    14701

    I had the Camera against the wall,
    The Enclosure is a Full 4 x 8 foot sheet of plywood with two Clear 24w X 18h inch Plastic sheet hanging from a 4 foot hinge.
    Leaving a 24 X 6...
  5. Have setup PrusaSlicer - Slic3r...

    Have setup PrusaSlicer - Slic3r quite some time ago using Cura Settings below, well today I am printing the first Model.

    Decided to test PrusaSlicer today as nothing else to do. My workload has...
  6. Thank You much. Though I have already tried many...

    Thank You much.
    Though I have already tried many slicers, including Prusa slicer.

    14675
  7. I have a plastic front which cover 90% of the...

    I have a plastic front which cover 90% of the front leaving about 10% of the bottom front that is used to draw air.
    In the back of my enclosure I have a bathroom fan that is used to suck the smelly...
  8. My 3D Printer enclosure has a light dimmer...

    My 3D Printer enclosure has a light dimmer control and a bathroom fan. I have a vent hole that the fan draws air from.

    When printing any model with air flow can ruin prints, I use only enough air...
  9. I understand though before I spend $150 dollars...

    I understand though before I spend $150 dollars would have to test any program purchased with a trial run. And this is not provided by simplify3d.
    curious aardvark can I connect to my 3D Printers...
  10. Replies
    5
    Views
    511

    If you looked at my 1st post you would see that I...

    If you looked at my 1st post you would see that I have a filament run-out sensor, on both of my 3D Printers.
    it was a simple project and was easily added to the controller and firmware.

    Final...
  11. Still today I use the older Cura 15.04.6 or if...

    Still today I use the older Cura 15.04.6 or if you like a Creality Slicer which is the a clone of Cura 15.04.6.

    Below are my settings


    14651

    14652

    14653
  12. Replies
    5
    Views
    511

    I have had filament break before I made my single...

    I have had filament break before I made my single sheet of plywood dual 3D Printer case.

    14635

    I can not say that the filament inside my enclosure has not broke,
    though it has reduced...
  13. This is probably correct You have a T8-8 which is...

    This is probably correct You have a T8-8 which is a 2mm pitch 4 start lead screw.
    This is different from a T8-2 which is a 2mm pitch single start lead screw.

    The difference is the if you rotate...
  14. I have posted about this before. T8-8 Lead-screw...

    I have posted about this before.
    T8-8 Lead-screw Drop with Gravity

    https://youtu.be/yFHEIdUf2Lw

    Image of three lead screws T8-8mm pitch (4 start), T8-2m pitch (single start), and All thread...
  15. Here is a couple ways that may help. When the...

    Here is a couple ways that may help.

    When the printer is just sitting if the steppers are disabled then the chance is higher that the Z-Axis will drop.
    I suggest that you should home your printer...
  16. I purchased a BigTree RepRap smart discount...

    I purchased a BigTree RepRap smart discount controller and had to make my own cables.

    I have posted about this before though will give a quick rundown again.

    Note that on this BigTree RepRap...
  17. Look here ...

    Look here

    https://3dprintboard.com/showthread.php?45232-Help-ID-board-Max-Micron-(Prusa-Mendel-I3-clone)
  18. The controller shown in your image is from a...

    The controller shown in your image is from a Hictop 3D Printer family, I have many different though very similar Hictop controllers.
    All work with the same firmware. the first two do not have an...
  19. Replies
    1
    Views
    287

    Try here #define CONFIGURATION_H_VERSION...

    Try here

    #define CONFIGURATION_H_VERSION 020005
    #define MOTHERBOARD BOARD_BTT_SKR_MINI_E3_V1_2
  20. Replies
    12
    Views
    1,002

    What Quarantine? If I do not show up for work...

    What Quarantine?
    If I do not show up for work will get fired. I am on the Essentials workers list.
    Job duties includes 90.1 % of the list below.

    Essential workers by industry, 2019

    ...
  21. Replies
    2
    Views
    538

    Fusion 360 for Makers : Design Your Own Digital...

    Fusion 360 for Makers : Design Your Own Digital Models for 3d Printing and CNC
    Autodesk Fusion 360 A Power Guide For Beginners And Intermediate Users
    A Beginner's Guide to 3D Modeling: A Guide to...
  22. I to started printing PLA for quite some time,...

    I to started printing PLA for quite some time, then one day decided to Print ABS.

    When I started printing PLA had some family members that hated the smell, so I built a case from a single sheet of...
  23. Replies
    10
    Views
    1,163

    Not sure where you got this funnel you can either...

    Not sure where you got this funnel you can either use supports of try printing another funnel/

    I have printed this funnel many times without supports

    https://www.thingiverse.com/thing:22024
    ...
  24. Replies
    6
    Views
    952

    You are learning by leaps an bounds you have...

    You are learning by leaps an bounds you have diagnosed what most noobs would never see.

    Good Going.
    Keep on at this pace an you will be helping others fix there problems.
    The solutions to most...
  25. Do not know much about Bukito 3D Printers....

    Do not know much about Bukito 3D Printers.
    Though I do know much of the 3D Printing problems can be attributed to the adjustments of the 3D Printer itself.

    1..Belt tension needs to be...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4