Close



Dig deeper, search our News website




Search:

Type: Posts; User: voodoo28

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    8,088

    I did the file comparison using Notepad++ and...

    I did the file comparison using Notepad++ and that was fine, except my version of Marlin was very old, as you can imagine many new features in the latest and some configuration file changes too.
    ...
  2. Replies
    7
    Views
    8,088

    I3v 12inch marlin rcbugfix..

    Has anyone successfully ported the latest rcbugfix to work with the I3v?

    I have tried and haven't had much success.
  3. Replies
    4
    Views
    5,639

    Hi Roxy, Thanks for the quick reply. I apologize...

    Hi Roxy, Thanks for the quick reply.
    I apologize for being so vague in my question. I took a few months hiatus from 3d printing and apparently a lot has changed!
    Im looking for the latest stable...
  4. Replies
    4
    Views
    5,639

    Roxy, can u please give me the link to the latest...

    Roxy, can u please give me the link to the latest stable version of marlin for the prusa I3?
  5. Replies
    8
    Views
    6,112

    Yea, i was surprised at how easy it was to print...

    Yea, i was surprised at how easy it was to print with, basically the same settings as PLA. I did no clean up either.
  6. Replies
    8
    Views
    6,112

    Finally had a chance to test out the Bamboo...

    Finally had a chance to test out the Bamboo filament.... Pretty Darn Cool..I like this stuff. . Going to order a roll of it!
    7318
  7. Replies
    8
    Views
    6,112

    I ordered the bamboo filament..received it...

    I ordered the bamboo filament..received it today.. Everything looks great..even got a free sample of fila silk filament..
  8. Replies
    8
    Views
    6,112

    Just placed my first order..!!! Nice to be in the...

    Just placed my first order..!!! Nice to be in the same state too!
  9. Replies
    21
    Views
    15,040

    I use Hatchbox religiously...never had a problem....

    I use Hatchbox religiously...never had a problem. $21 a roll from Amazon is perfect!
  10. Replies
    28
    Views
    11,816

    lol....Ive had a proximity sensor on hand for a...

    lol....Ive had a proximity sensor on hand for a while now...but havent found a way to install with both my extruders yet.
  11. Replies
    2
    Views
    4,053

    Why not just pour your beer into the Coffee cup...

    Why not just pour your beer into the Coffee cup directly? :confused:
  12. Replies
    28
    Views
    11,816

    What brand of servo are you using?

    What brand of servo are you using?
  13. Replies
    28
    Views
    11,816

    i was thinking of doing that , replacing it with...

    i was thinking of doing that , replacing it with a digital servo rather than an analog..better quality.
    BUT.... the same thing is happening to a friend of mine whos only had the new servo working...
  14. Replies
    28
    Views
    11,816

    Im telling you, that's whats happening to...

    Im telling you, that's whats happening to me....it works fine, then craps out, then works fine again.
    I have even swapped out the gears in servo , to remove any slop it might of had.
  15. Replies
    28
    Views
    11,816

    The reason i chimed in is because I too am having...

    The reason i chimed in is because I too am having the same issue... All of a sudden my servo is a few degrees off about 60% of the times.. It never used to to do that.. I'm thinking it has something...
  16. Replies
    28
    Views
    11,816

    Rather than changing your numbers that were known...

    Rather than changing your numbers that were known to work...shouldnt you be checking as to why it is no longer working correctly? Firmware doesnt change because it sits over night or a period of...
  17. Replies
    82
    Views
    34,706

    Your Prints are looking Great!

    Your Prints are looking Great!
  18. Replies
    41
    Views
    34,809

    1.75 here...with liner in the extruder block and...

    1.75 here...with liner in the extruder block and hot end
  19. Replies
    14
    Views
    22,404

    I also Live in South Fl...and print from my...

    I also Live in South Fl...and print from my garage, ive had my printer in there for almost 8 months now and no issues at all..if anything it helps with ABS not warping due to the warm room .
    Also...
  20. Replies
    41
    Views
    34,809

    I can say after using the E3D with your dual flex...

    I can say after using the E3D with your dual flex for over 4 months...oozing is not an issue....using some simple retraction settings in S3D.
    A new Feature in S3D is the ooze shield, specifically...
  21. Replies
    8
    Views
    7,810

    Shouldn't you be using Type 1?

    Shouldn't you be using Type 1?
  22. Replies
    8
    Views
    7,810

    What are your temps? Did you do the PID tuning...

    What are your temps?

    Did you do the PID tuning after changing from the Hex over to E3D? They both use different thermisters did you change that in Marlin?
  23. Replies
    37
    Views
    16,879

    That's the same reason why i went to the dual...

    That's the same reason why i went to the dual flex setup..mine kept skipping.
  24. Replies
    101
    Views
    69,860

    No, actually im using it with a Dual setup..but i...

    No, actually im using it with a Dual setup..but i don't see why you couldn't just mount one side only. Then when you are ready, you can setup the other side. Your gears should spin freely with no...
  25. Replies
    101
    Views
    69,860

    here is the thread ...

    here is the thread http://3dprintboard.com/showthread.php?10480-Itty-Bitty-Single-Extruder
    towards the end you'll find my remix for the E3d Hot end.


    My setup would skip too..which is why i...
Results 1 to 25 of 212
Page 1 of 9 1 2 3 4