Close



Dig deeper, search our News website




Search:

Type: Posts; User: blairmi2

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    2,120

    z-axis consistant gap

    Hello,

    I have a powerspec 3d pro but figured its close enough to the FFCP that someone here will know. I have a consistent issue on my z-axis where I'll get a gap/slight shift regardless of...
  2. turns out it was a z-axis offset issue. ...

    turns out it was a z-axis offset issue. increasing extrusion multiplier and overlap was a bandaid. honed it down to a .1mm offset.
  3. Upgraded to micro-swiss all metal - gaps in infill

    I had a nozzle jam on me the other day and decided to upgrade one extruder to the micro swiss all metal hot end below (.4mm). I print PLA and didn't change any slicer settings but immediately...
  4. Replies
    2
    Views
    3,497

    I haven't only because I can't seem to find a...

    I haven't only because I can't seem to find a download of the original firmware anywhere...my understanding is it was an early release of sailfish 7.7 with the LCD screen modified to say "1.2 Power...
  5. Replies
    2
    Views
    3,497

    Another toolhead offset thread

    I have a powerspec 3d pro printer that was printing dual extrusions models fine until I upgraded to sailfish 7.7 r01591 (Creator X firmware). My printer is not accounting for the offset on the left...
  6. Replies
    6
    Views
    5,593

    Fortunately I haven't run into this problem. ...

    Fortunately I haven't run into this problem. Maybe try isolating it to the HBP or the wires themselves. Unlikely to be the MB.
  7. Replies
    6
    Views
    5,593

    yup, just checked the wires on the MB, gave them...

    yup, just checked the wires on the MB, gave them a wiggle and tightened them down. Works fine.

    Thanks for posting!
  8. Replies
    6
    Views
    5,593

    any news on this? I'm now experiencing the same...

    any news on this? I'm now experiencing the same problem
  9. Replies
    16
    Views
    10,932

    I agree, none of those clips worked well...so i...

    I agree, none of those clips worked well...so i modified a set and made my own! Holding strong the last 30hrs of printing and very easy to adjust when needed since there are wingnuts on the bottom...
  10. Replies
    12
    Views
    6,932

    can you share a picture?

    can you share a picture?
  11. Replies
    16
    Views
    10,932

    some great posts everyone! Thanks for all the...

    some great posts everyone! Thanks for all the input/options.

    After heating the stock buildplate to 60C for PLA prints, I still had leveling issues in the front right quadrant. I end up with wavy...
  12. Replies
    16
    Views
    10,932

    Thanks for the heads up on the PrintinZ flex...

    Thanks for the heads up on the PrintinZ flex plate, i'll check it out
  13. Replies
    16
    Views
    10,932

    actually I wasn't...i'll give that a try before...

    actually I wasn't...i'll give that a try before purchasing anything and report back. I've been printing with PLA anyway and use a 60C bed with blue scotch 3M tape.
  14. Replies
    16
    Views
    10,932

    i consistently have problems with the lower right...

    i consistently have problems with the lower right part of the plate (closest to the door) while the rest of the plate is fine. instead of smooth lines I get wavy lines but i've lived with it. ...
  15. Replies
    16
    Views
    10,932

    after reading this post it seems that I can...

    after reading this post it seems that I can remove the aluminum bed and forget using the shim for the z-axis....
  16. Replies
    16
    Views
    10,932

    1/8" glass bed installation question

    Consistent with most, my aluminium bed that came with my Power Spec 3D pro is warped. I would like to replace it with a 1/8" sheet of Borosilicate glass but information seemed to be scattered across...
  17. Replies
    2
    Views
    1,779

    solved: printing at 230C fixed

    solved: printing at 230C fixed
  18. Replies
    7
    Views
    13,020

    I've also experienced the clicking when trying to...

    I've also experienced the clicking when trying to load filament at 210C with a less than ideal filament tip. Always start with a good tip and I now load at 220.
  19. Replies
    2
    Views
    1,779

    first layer issues

    hello!

    I'm using a powerspec 3d pro with S3d 3.0.1. I've had the printer about a week and i'm trying to print a golf tee from the following thingverse link. You can see in the image my printer...
Results 1 to 19 of 19