Search:

If you have to go with two or more heaters, I believe the better alternative would be to get a controller with multiple outputs to control each zone independently and then connect a single...

Welcome to the forum.

What do you mean you printed 10 pieces? This looks like one of those prints that prints as a conjoined print in place toy.

Doesn't it all print at once assembled?

Or...

Releveled or rehomed? It sounds like you needed to home it if it was running above the bed. Anyway, glad you figured it out.
Good luck and best wishes.

I had to look up what this was, and I'm still not real sure. Anyway, I see it mentioned with the Ender 3 a few times but not the Pro version. Not sure how much of a difference there is between the...

If you're open to Fusion 360, here is a whole 30 lesson course for free on how to model and design in autodesk.

https://youtu.be/d3qGQ2utl2A?si=plUc4h8YZ2ot_sZP

That looks like it should do the job starting out. If it is working for your needs that's all that matters.

I pulled this video for you. Just something to consider as you get more into the hobby....

Granted I only print at work, but I use Grainger and feel like I get decent pricing.

As for why some may be more than others, some if it is the reel. If you can use Cardboard vs Plastic that's a...

Fusion is my go to for sure. I print mostly for work, not as work but for my place of employment. Anyway, a friend of mine suggested this course on Fusion, Learn Fusion 360 in 30 days. It's super...

The printers I used just sat on a spare desk, nothing special and for the most part I got good prints off of them. It was more about the time I spent with prepping the bed, for me. When I first got...

If you can't print ABS I think you might struggle to print PETG, or at least I did. I was looking for something a bit stronger than PLA and PETG had some of the qualities I was looking for over PLA...

So I was getting these marks and I felt like I was also having issues with my prints due to the feed rate of my filament. Like you I was getting scaring on the sides of my filament that I would...

My Prusa MK 3 is direct drive vs my Creality printer which has a long tube that guides the filament to the extruder. A quick Google image search will show you the differences between the two.

You...

I'm using the same brand printer and I've never tried slowing down the first layer. I see where that would help but for me, I usually clean the plate really well to get good adhesion, and then bump...

Pretty sure this would qualify as a tip. A friend of mine was struggling with a project and happened upon this series and then turned me on to it. It just so happened that I was looking for a...

I'm on day 10 or 11 and this is pretty straight forward and starts off simple. It's better if you have dual monitors and can run the video on one while doing the thing on the other.

Not sure if...

That is super clean. Nice work. I'm lost when it comes to modeling.

You could start the print at an angle and only print some of it vs fully committing and trying to print it all. I do small test prints a lot to cut down on wasted time later if something fails. Try...

I've had a similar experience where my print may have succeeded if only the slicer had made longer straight lines instead of jumping around. I searched this question and all I found was there was no...

@patriciaf334, when you ask a question like this you're supposed to tell us your pick too, but on that note, I was into COD forever. Played Black Ops 4 League as recently as last weekend. DMZ in MW2...

Hello everyone,
I may be posting this in the wrong place but I didn't find a new to the forum or welcome thread and since this would mainly be off topic I figured I would post here. If I'm wrong...

Hey how's it going? I've suffered the issue of the broken triangles not just in cylinders but in other "hollow" prints.

What infill percentage are you trying to achieve? For me the lower the...