Close



Dig deeper, search our News website




Search:

Type: Posts; User: plackslayer

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. I have mine working. It's connected up to the...

    I have mine working. It's connected up to the second power ports next to E1. I didn't have to change any pin settings.

    My main problem is getting sliced code to activate fan 2 when starting a...
  2. LCD Screen off - RAMBo board - tl;dr - popped a fuse

    So I was recalibrating the dual extruder setup because it was a bit off on my last print, no idea what I did but the LCD wouldn't come on. Figured I might need a reflash because when I plugged it...
  3. Broke my build plate glass - might be more damage in the extruder

    It seems after breaking my glass due to not checking the nozzel for hardened plastic from a previous print, when homing z it just kept going because the endstop never triggered.

    Something else...
  4. I have the Z-BabyStepping and...

    I have the Z-BabyStepping and Double-Click-for-Babystepping on. Makes it easy.

    I'm having ABS adhesion issues with this old ABS spool, but I'm not worried.

    I need to mess with slic3r settings...
  5. About to do the G26 steps: Starting with this...

    About to do the G26 steps:

    Starting with this map


    Bed Topography Report:
    (0,9) (9,9)
    (11,309) ...
  6. Leveling the bed now using your guidance. It's...

    Leveling the bed now using your guidance. It's much easier than the crappy level I was using.

    Here are a couple photos of the 50 mm offset and a small mod I did to help keep the x-carriage from...
  7. I'll post pictures tonight - maybe I'm measuring...

    I'll post pictures tonight - maybe I'm measuring it wrong - who knows. I've been known to do stranger things...
  8. 50mm seems odd to me as well considering Clough32...

    50mm seems odd to me as well considering Clough32 says it should be something like 27 on the Itty Bitty Flex Dual Extruder... BUT when I measured it said 50 on the nose.

    I switched my settings...
  9. Prints just fine with a single nozzle. Now I'd...

    Prints just fine with a single nozzle. Now I'd like to get UBL working to make things even better but I keep having issues.

    It attempted to probe off the plate...

    To get my Z probe settings I...
  10. Stuttering was because of a failing solder I did...

    Stuttering was because of a failing solder I did - fixed.

    Lead Screws needed new base plates printed to hold the Z Motors like 2mm further away from the frame than the threaded rods base plates -...
  11. Ok well it seems switching to the lead screws vs...

    Ok well it seems switching to the lead screws vs threaded rods has caused an issue. The printed parts I made look like they may be too far away from the X-carriage. This makes it bend the rods away...
  12. Yeah I have toned the servo angels down a lot. ...

    Yeah I have toned the servo angels down a lot.

    Now I have a new problem... the Z axis second motor is just stuttering, not going up and down...
  13. #define Z_SERVO_ANGLES {104,30} // Z Servo...

    #define Z_SERVO_ANGLES {104,30} // Z Servo Deploy and Stow angles


    Found this to get my servo settings I believe ... correct~ish.

    I'll play some more but I do believe that my setting of
    ...
  14. In the configuration.h file - I have set ...

    In the configuration.h file - I have set

    #define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 615.0, 615.0 }


    That is for the itty bitty flex dual extruder(s) rate of 615.0 and the Lead Screw...
  15. Attempted a print - worked perfectly. printed a...

    Attempted a print - worked perfectly. printed a pair of parts to switch from threaded rods to lead screws. The part that you screw the brass nut into.

    With those printed - I found an...
  16. ok well I got the cable situation fixed but...

    ok well I got the cable situation fixed but now...

    Forcing an UBL didn't extend the probe - I did it manually and it worked until it went off the bed in the X direction by maybe 1cm too far.
    ...
  17. So swapping the pinout to #define SERVO0_PIN...

    So swapping the pinout to

    #define SERVO0_PIN 5

    I have found that power is on on the PWM header. Now after testing my wiring extension it only has 2/3 working... going to remake that sometime...
  18. I'm wondering if I can somehow switch SERV0 PIN...

    I'm wondering if I can somehow switch SERV0 PIN 22 to SERV0 PIN 5 and keep it connected like I have it...

    I'll try this later tonight and if that doesn't work - try the LED trick to hunt down...
  19. Which is why I'm reaching out for help lol.

    Which is why I'm reaching out for help lol.
  20. https://reprapwilson.discoursehosting.net/uploads/...

    https://reprapwilson.discoursehosting.net/uploads/db7887/original/1X/84888e3fcaf88e680bbb7a806651ce8b93186d52.png
  21. I have the 3 pins connected to the PMWEXT...

    I have the 3 pins connected to the PMWEXT connection - pins 1(+5V), 2(Grnd), and 5(Signal).

    Do I need to move the connection to a different place?
  22. Configuration_adv.h /** * Marlin 3D...

    Configuration_adv.h


    /**
    * Marlin 3D Printer Firmware
    * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
    *
    * Based on Sprinter and grbl.
    * Copyright (C) 2011...
  23. Ok so I have updated to the nightly build of...

    Ok so I have updated to the nightly build of Marlin - I have attempted to fix my issues but I still cannot get the the servo for the z probe to extend/retract.

    I have tested the wiring and it...
  24. Attempted to update firmware... now I'm stuck

    A while ago I printed the parts for the Itty Bitty Double FLEX V2Extruder and picked up the hardware to make it... Finally got around to putting it all together and am now stuck...

    I have the...
  25. Replies
    48
    Views
    15,897

    In the process of building it now - soldering is...

    In the process of building it now - soldering is going slow because I keep getting interrupted...

    Question, if the nozzles are about 26.5mm apart is this ok or do they need to be exactly 27mm. ...
Results 1 to 25 of 44
Page 1 of 2 1 2