Close



Dig deeper, search our News website




Search:

Type: Posts; User: xayoz

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    523

    if you got a film, you did not clean off the...

    if you got a film, you did not clean off the remaining soap properly, keep cleaning and it will be good. But if you got glass, then you shouldn't need to worry about that for a while. I like the...
  2. Replies
    4
    Views
    407

    a quick google search for zonestar firmware...

    a quick google search for zonestar firmware brought up their main download page, so you could take a look at that
  3. Replies
    6
    Views
    523

    Isopropyl, preferably 99%, do not use beer

    Isopropyl, preferably 99%, do not use beer
  4. Replies
    6
    Views
    523

    step 1 - clean the bed with soap and water step...

    step 1 - clean the bed with soap and water
    step 2 - clean the bed with IPA
    step 3 - level the bed again with the paper method (go around 3 or 4 times)
    step 5 - reprint your calibration print and...
  5. Replies
    1
    Views
    271

    More info would be good. How you are describing...

    More info would be good. How you are describing "sensor" seems like an ABL, so is it BLTouch, EZABL, Kava Lite, something else? Which main board, original, BTT Mini 1.2, something else?

    If it...
  6. Thread: Skr mini e3 1.2

    by xayoz
    Replies
    1
    Views
    264

    skr mini e3 already has bootloader. Just put...

    skr mini e3 already has bootloader. Just put your new bin file on the root of the card, plug it in and turn on your machine. there will be a delay before the screen displays anything, but when it...
  7. Thread: Prusa MK3S

    by xayoz
    Replies
    0
    Views
    256

    Prusa MK3S

    A little disappointed in my new Prusa MK3S. It arrived at my door May 5, so I've had about a month and a half. Now I can't print anything because I get mintemp bed error. This happened about 20...
  8. Replies
    4
    Views
    925

    magnetic bed should be fine, I have the same on...

    magnetic bed should be fine, I have the same on my Ender 3 Pro with no issues. Just need to clean it now and then with soap and water, then with ipa

    as far as filaments, I have had good luck with...
  9. Thread: PETG Woes

    by xayoz
    Replies
    3
    Views
    586

    ok, problem solved. The globs were from a...

    ok, problem solved.

    The globs were from a leak. I accidentally loosened the heatbreak when changing the nozzle, tightened everything up, it no longer leaks.

    As far as the textured sheet, I was...
  10. Thread: PETG Woes

    by xayoz
    Replies
    3
    Views
    586

    Actually I think I found my blob problem. I'll...

    Actually I think I found my blob problem. I'll try your suggestions if tightening this up and changing the nozzle doesn't help. Thanks.

    1457314573
  11. Thread: PETG Woes

    by xayoz
    Replies
    3
    Views
    586

    PETG Woes

    I finally feel confident enough to move away from PLA and try something else, so I'm trying PETG.

    I'm using Prusa MK3S and slicing in Prusa Slicer with the Prusament PETG default settings. And...
  12. Replies
    4
    Views
    975

    100% with you on BTT being awesome. I know you...

    100% with you on BTT being awesome.

    I know you don't like Creality, but I put BTT SKR Mini E3 1.2 in my Ender 3 Pro and it is night and day. Built in TMC2209 so super silent. Dedicated spot for...
  13. Thread: Elegoo Mars???

    by xayoz
    Replies
    2
    Views
    689

    if you're looking at miniatures, resin is...

    if you're looking at miniatures, resin is supposed to be good (I have not tried resin personally, so grain of salt)

    For cosplay pieces, 100% what Aardvark said, go with FDM
  14. Replies
    1
    Views
    465

    next time don't scrape, just heat to about 220 or...

    next time don't scrape, just heat to about 220 or 230 and gently peel it off
  15. you want to use a piece of printer paper when...

    you want to use a piece of printer paper when leveling your bed. You want it to scrape the paper, but not grip it. After you make sure everything is properly leveled, you will find in your menus...
  16. Replies
    6
    Views
    956

    it started again, and on further investigation it...

    it started again, and on further investigation it turned out that I had mounted the gear on the Y axis just a hair to close to the motor, so it was intermittently rubbing
  17. Replies
    9
    Views
    2,228

    Because a moderator constantly refers to the...

    Because a moderator constantly refers to the Ender as a "garbage" knockoff of Prusa...so there is my honest opinion on the comparison since I have both...
  18. Replies
    6
    Views
    956

    I put a bit of the grease that came with the...

    I put a bit of the grease that came with the machine onto the rods, moved the axes to spread it, and the noise is gone. Should not have listened to the manual when it said not to lube the bearings. ...
  19. Replies
    12
    Views
    1,316

    I agree with Aardvark that Creality users post...

    I agree with Aardvark that Creality users post more problems than any other manufacturer, but I believe there is a valid reason for it other than "they're all junk"...I believe Creality makes a great...
  20. Replies
    6
    Views
    956

    Original Prusa MK3S squeaking loudly

    I have a very loud intermittent squeak in my Prusa MK3S. It's hard to tell if it's from x or y axis, but what did I assemble incorrectly? Do I have a bad bearing, is a belt too tight?

    ...
  21. Replies
    81
    Views
    49,363

    Sticky: I can't speak to the CR6, but the Ender 3 you...

    I can't speak to the CR6, but the Ender 3 you will need some upgrading for what you describe. The Ender 3 series does not have thermal runaway protection out of the box, so you would need to update...
  22. Thread: Start G-Code

    by xayoz
    Replies
    2
    Views
    439

    I have the same DD. I did not change start...

    I have the same DD. I did not change start gcode, but instead adjusted bltouch mount offset in the firmware. What solution fixed the issue for you?
  23. Replies
    3
    Views
    367

    The best thing is to learn with it stock first,...

    The best thing is to learn with it stock first, then start upgrading to solve issues or perceived issues.
    For example:

    Yellow springs, many people use the OE springs and they work fine, but in...
  24. Replies
    9
    Views
    2,228

    686, I am definitely with you. I have an...

    686, I am definitely with you. I have an original Prusa MK3S and a Creality Ender 3 Pro. While Aardvark is right that the direct drive and linear rods make the Prusa a nicer machine that admittedly...
  25. Replies
    17
    Views
    4,840

    Creality white and Hatchbox have been good for...

    Creality white and Hatchbox have been good for me, going to be trying esun this week
Results 1 to 25 of 49
Page 1 of 2 1 2