Close



Dig deeper, search our News website




Search:

Type: Posts; User: Bikeracer2020

Search: Search took 0.00 seconds.

  1. Replies
    81
    Views
    49,628

    Sticky: I think this thread should be titled 'Post spam...

    I think this thread should be titled 'Post spam here' with all the spam that gets posted on it
    Same spam post, posted six minutes after first one.
  2. Replies
    2
    Views
    365

    Done the calibration twice just to check, X-axis...

    Done the calibration twice just to check, X-axis and Y-axis line up spot on. There is a two coloured square file included and that prints okay.
    When i move the extruder gantry gently without power...
  3. Replies
    2
    Views
    365

    Creator 3 supports problem

    I have no problem printing from either extruder, however when I try to print something using one extruder for the print and the other for supports I get severe layer shift.
    See pics. This printer is...
  4. Whatever you buy do not get it from Banggood,...

    Whatever you buy do not get it from Banggood, their return or refund policy is meaningless and if you have a problem you'll just be out of pocket. Just look at some independent review sites. I wish I...
  5. Replies
    4
    Views
    1,251

    It's a vinyl cutter plotter, that part looks like...

    It's a vinyl cutter plotter, that part looks like it goes in the end of a roll of vinyl. Bit like a toilet roll holder only bigger.
  6. Can't advise on printer choice but if you buy one...

    Can't advise on printer choice but if you buy one from Banggood you will have no hope to return or get a a refund if it's faulty.
  7. Replies
    0
    Views
    407

    I am looking to buy a Qidi X Max

    Does anyone in the UK know where they have a Qidi X Max in stock ?
  8. Replies
    7
    Views
    836

    I did try Repetier Host but that has no profile...

    I did try Repetier Host but that has no profile for the printer.
    MatterControl has a connection wizard but that could not find the printer and get a profile after connecting the USB cable. Not a lot...
  9. I'm in the UK and presume the consumer laws will...

    I'm in the UK and presume the consumer laws will be similar in most parts of the democratic world.

    Dealing with Banggood has been a hard lesson learned, I think most people are used to dealing...
  10. Replies
    7
    Views
    836

    Being a complete beginner with no previous...

    Being a complete beginner with no previous experience so no idea what the G code looks like.
    I put MatterControl on my computer and connected it via USB. The MatterControl could not find the printer...
  11. SOLD TwoTrees Saphire Pro

    I have a brand new Sapphire Pro that will not actually print, at a guess it's the mainboard.
    The extruder works, the bed and hot end both get hot, the move controls on the touchscreen work and the...
  12. Replies
    5
    Views
    663

    All I can say is "good luck trying to claim from...

    All I can say is "good luck trying to claim from Banggood".
    Like me you'll just be another sucker they have taken money from with no intention of honouring their return or refund guarantee.
  13. Replies
    26
    Views
    3,103

    I bought a TwoTrees Sapphire Pro, carefully...

    I bought a TwoTrees Sapphire Pro, carefully assembled it, leveled the bed, loaded and extruded the supplied filament, loaded the supplied SD card with a test print file on it.
    Then nothing else...
  14. Replies
    7
    Views
    836

    The icons show somethings which are self...

    The icons show somethings which are self explanatory as in ....load and unload,heat bed and hot end etc.

    There is one for autolevelling but no instructions as to how to use the supplied push on...
  15. I've just bought a Saphire Pro printer from...

    I've just bought a Saphire Pro printer from Banggood which is faulty and does not work.
    Trying to send it back for a refund but am being met with being told they have to contact their supplier first...
  16. Replies
    81
    Views
    49,628

    Sticky: Suggestion

    I am completely new to 3D printing and bought a TwoTrees Saphire Pro from Banggood.

    It refuses to print anything from the supplied SD card, the USB connection does not work. No documentation other...
  17. Replies
    7
    Views
    836

    Saphire Pro problem

    Complete new user here!

    I assembled a Saphire Pro corexy printer and I'm wondering if the mainboard is faulty or the problem is me ?

    The auto levelling works and the extruder works but when I...
Results 1 to 17 of 24