Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberta3D

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Hi fred_dot_u, Thank you for catching that...

    Hi fred_dot_u,

    Thank you for catching that typo! It is a second generation PSP container and it is available through our website:

    http://www.kudo3d.com/product/psp-resin-container/

    It has...
  2. Replies
    2
    Views
    23,454

    Hi Michael, Jon mentioned that he had helped...

    Hi Michael,

    Jon mentioned that he had helped you troubleshoot your issue offline yesterday. Please let us know if you have any further questions.

    Regards,

    Roberta
  3. Kudo3D Introduces 2nd Generation PSP Container

    We recently launched our second-generation passive self-peeling (PSP) resin container. Our testing of the container has yielded excellent results. We have completed 52 prints in a row! We are...
  4. Thread: Infill

    by Roberta3D
    Replies
    5
    Views
    63,297

    Peerless Design, The ABS test was printed...

    Peerless Design,

    The ABS test was printed solid but that part is small. We were discussing the larger models like the tall statues printed. Thank you!
  5. Thread: Infill

    by Roberta3D
    Replies
    5
    Views
    63,297

    Hughes, If necessary, we add supports inside...

    Hughes,

    If necessary, we add supports inside to resist shrinkage. The infill pattern for FDM requires special software to do it. We will look into the possibility to adapt FDM's software to do...
  6. Thread: Infill

    by Roberta3D
    Replies
    5
    Views
    63,297

    Albert, We will definitely take your suggestion...

    Albert,
    We will definitely take your suggestion into consideration. We just tested our first ABS-like sample last week. This will be an on-going process. Thank you.
  7. Thread: Infill

    by Roberta3D
    Replies
    5
    Views
    63,297

    Infill

    We received several questions in the comment section of our Kickstarter regarding infill.

    Hugues Laliberte:

    "@Kudo3d, you said below:
    We do not print solid models that has large...
  8. Replies
    15
    Views
    50,346

    Hi Valter, If you would like to back us on...

    Hi Valter,

    If you would like to back us on Kickstarter, which will provide you with the lowest price, just follow these steps. On the Kickstarter page, press on the green button which reads "Back...
  9. Replies
    15
    Views
    50,346

    Hi Valter, We intend to begin taking...

    Hi Valter,

    We intend to begin taking pre-orders after our Kickstarter campaign ends.

    Thanks,

    The Kudo3D Team
  10. Replies
    16
    Views
    45,306

    What are you going to make with the Titan 1?

    We would like to invite you to share with the community what you plan on creating with your Titan 1! Later, when we have a users' gallery, it will be exciting to see your ideas after they have come...
  11. Hi Eddie, Here is a link to the Fox Business...

    Hi Eddie,

    Here is a link to the Fox Business segment:
    ...
  12. Replies
    37
    Views
    92,425

    Many of you were asking to see results of...

    Many of you were asking to see results of modifying the lens. Thank you for helping us select this graduation ring to print. We were able to achieve XY resolution of 26 microns and Z layer thickness...
  13. Hugues, We will offer ABS like material in the...

    Hugues,

    We will offer ABS like material in the near future. Layer interface failure is rarely seen with SLA.
    It only happens when the resin is underexposure or when the lifting speed is too...
  14. Titan 1 Met Its Kickstarter Goal in 2 Minutes!

    The Titan 1 was funded on Kickstarter in less than 2 minutes! We would like to extend a thank you for your enthusiasm and support. Our backers are playing an instrumental role in not only the growth...
  15. Replies
    15
    Views
    50,346

    Hi Feign, Yes. Changing printing resolution...

    Hi Feign,

    Yes. Changing printing resolution is done by changing the size of projected area. If low viscosity resin is used, there is no limit on the printing height. However, high viscosity...
  16. Replies
    15
    Views
    50,346

    Feign, Thank you for your excellent questions....

    Feign,

    Thank you for your excellent questions. The maximum XY build size is determined by the projected area. For 100 micron pixel size, 1920x1080 resolution represents 192mm x 108 mm which is...
  17. Replies
    2
    Views
    5,138

    RedSox2013, We are extremely excited too! Many...

    RedSox2013,

    We are extremely excited too! Many people are reticent about buying an SLA printer because of the cost of both the unit and the filament. Our printer is compatible with most vendors'...
  18. Replies
    2
    Views
    5,138

    Titan 1 Update

    To celebrate the upcoming May 27th launch of the Titan 1, we are giving away a free Kudo 3D t-shirt! For a chance to win, follow us on Facebook and you will be automatically entered to win. The...
  19. Replies
    15
    Views
    50,346

    Larry and Maggie, Thank you so much for your...

    Larry and Maggie,

    Thank you so much for your interest in Titan 1 and Kudo3D. We are flattered by your price approximation! During our Kickstarter campaign, which will launch on May 27th at 8:30am...
  20. In order to accommodate media coverage of the...

    In order to accommodate media coverage of the Titan 1, we have had to push back the Kickstarter launch date. It will now be released on May 27th at 8:30am PST. There has been a great deal of interest...
  21. intohim, We are working on compiling more...

    intohim,

    We are working on compiling more videos. If you would like to visit our website at www.kudo3d.com, we have a subscription option available. We send our subscribers updates on the Titan 1...
  22. Replies
    1
    Views
    4,007

    Hi everyone, In order to accommodate media...

    Hi everyone,

    In order to accommodate media coverage of the Titan 1, we have had to push back the Kickstarter launch date. It will now be released on May 27th at 8:30am PST. There has been a great...
  23. Steve S, Yes, it is. We are planning to share...

    Steve S,

    Yes, it is. We are planning to share even more photos in the near future :)
  24. Thank you for sharing our video. :) This 9.5...

    Thank you for sharing our video. :)

    This 9.5 inch Eiffel Tower was completed in about 7 hours. We use a "patent pending", flexible, passive self-peeling (PSP) resin container, which minimizes the...
  25. Replies
    4
    Views
    3,331

    1235 It looks like it worked! Here is a close...

    1235

    It looks like it worked! Here is a close up!
    1236

    Here is an artsy picture of it. :)

    I used the Titan 1 by Kudo3D. It hasn't been officially released yet, not until May 20th, but I...
Results 1 to 25 of 31
Page 1 of 2 1 2