Close



Dig deeper, search our News website




Search:

Type: Posts; User: DrMacZed

Search: Search took 0.00 seconds.

  1. Replies
    187
    Views
    314,003

    Sticky: Direct drive Prusa i3V with Hexagon hotend

    Greetings all,

    Here is a little something I fabricobbled over the last couple weeks. I converted my older i3V from the Greg's wade extruder to a direct drive; mostly because I have gone through...
  2. Replies
    8
    Views
    7,104

    Well there was a small peice of paper in with one...

    Well there was a small peice of paper in with one of the boxes of parts that had E-Steps 814.xxx so I foolishly assumed that that was the proper setting for the extruder. Now i need to get less...
  3. Replies
    8
    Views
    7,104

    Well, after a lot of cursing and head scratching,...

    Well, after a lot of cursing and head scratching, I figured it out. I had the E-steps on the extruder set way, way too high. They were over 800 I cranked them down 100 steps at a time until I got...
  4. Replies
    8
    Views
    7,104

    10" Pegasus extruder issues....

    Greetings all,

    I have a 10" Pegasus that doesn't seem to want to feed filament properly. When extruding the drive pulley skips making a godawful clickclickclickclick noise and the filament does...
  5. Replies
    18
    Views
    14,787

    I made enclosures for both my printers, 8" i3v...

    I made enclosures for both my printers, 8" i3v and a 10" Pegasus. they were made from fairly cheap materials, 3/4"x 1/16" aluminum angle from the hardware store, Foamboard with aluminum foil glued to...
  6. Replies
    5
    Views
    13,994

    I have an i3v 8" and a Pegasus 10" both with...

    I have an i3v 8" and a Pegasus 10" both with heated bed relay.
  7. Replies
    5
    Views
    13,994

    Thanks. I'll give that a try.

    Thanks. I'll give that a try.
  8. Replies
    5
    Views
    13,994

    Gcode for auto shut off?

    Hello,

    I was wondering if there is a way to have the printer auto shut off the heated bed when finished with a print; the hot end shuts off but the bed does not. Would I need to add custom gcode...
  9. Thread: 123D Design

    by DrMacZed
    Replies
    3
    Views
    6,289

    I have had good luck with FreeCad...

    I have had good luck with FreeCad http://www.freecadweb.org/
  10. Replies
    2
    Views
    3,698

    Put your printer inside an enclosure. I too had...

    Put your printer inside an enclosure. I too had print issues due to cold ambient temps. I made an enclosure for my printer and my prints have never looked better. See this post for what I did. ...
  11. Replies
    187
    Views
    314,003

    Sticky: Thank you. As for knowing if the enclosure will...

    Thank you. As for knowing if the enclosure will eliminate or at least greatly reduce warping, only time will tell. I haven't had a chance to calibrate my printer yet to test it properly. I did run a...
  12. Replies
    187
    Views
    314,003

    Sticky: Howdy all, I was having horrible warping...

    Howdy all,

    I was having horrible warping problems when printing ABS. From this great forum I learned that the root cause of my warping issues was cold, my printer lives in my workshop in the...
  13. Replies
    4
    Views
    3,275

    OK I will try that next. Thank you Roxy.

    OK I will try that next. Thank you Roxy.
  14. Replies
    4
    Views
    3,275

    No, I was a total bonehead and failed to make a...

    No, I was a total bonehead and failed to make a copy of the original Configuration.h file. I was trying to unlock some of the extra features available though the LCD interface to better calibrate my...
  15. Replies
    4
    Views
    3,275

    Question about a reflash..

    Good afternoon,

    I tried searching this forum and Google for a few days to no avail. I have a Prusa i3v 8". I recently started tinkering with the marlin code and broke it. I was able to do a...
Results 1 to 15 of 15