Close



Dig deeper, search our News website




Search:

Type: Posts; User: qwiktune

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    2,576

    CR10 v2 SD Extension Issue

    So I want to tuck my control box under the table my CR10 v2 is on, so I want to extend my sd card out at the edge of the table. I got an SD extension (full size to full size since the v2 uses a full...
  2. Replies
    0
    Views
    1,564

    Creality CR10 v2 Wire Extension Help

    Looking to put my CR10 v2 control box under the desk my printer sits on but I need like 5 more inches on the 16 pin connector at the base of the rail to reach. Anyone know where I can find a plug and...
  3. Replies
    8
    Views
    6,096

    I mean its good enough that I can understand...

    I mean its good enough that I can understand exactly what it says and theres a link to something never even mentioned in the thread lol. I mean Xerox is no where near Creality Ender lol
  4. Replies
    8
    Views
    6,096

    Well thats pretty random

    Well thats pretty random
  5. Replies
    8
    Views
    6,096

    ehhhh, what? xerox? no

    ehhhh, what? xerox? no
  6. Replies
    14
    Views
    13,377

    I'm already improved it by changing my retraction...

    I'm already improved it by changing my retraction to 1 from 3. Theres still a hair of stringing by its easily cut with a blade. I think my problem was when it switched from the leg with the holes...
  7. Replies
    8
    Views
    6,096

    So I figure out it was the X axis bar when...

    So I figure out it was the X axis bar when assembled stright was actually curving down a few mm (where I was getting the nozzle being closer on one side than the other even when all 4 corners where...
  8. Replies
    8
    Views
    6,096

    Ender 3 X Axis Bar Flawed or User Error?

    Long story short I just bought the Ender 3 as a spare printer to prototype on, printers were ok but I hated how soft the bed springs were so I upgraded to stiffer ones (to hopefully not have to...
  9. Replies
    14
    Views
    13,377

    I wasnt able to get to it. I had actually bought...

    I wasnt able to get to it. I had actually bought another printer, (Ender 3x) so I had a print I could do prototyping on while printing parts on the other, and ended up putting it together last night....
  10. Replies
    14
    Views
    13,377

    This should help. I'm going to private msg you...

    This should help. I'm going to private msg you the STL file.
    13499
  11. Replies
    14
    Views
    13,377

    I've been using Cura, but I have a version of...

    I've been using Cura, but I have a version of Simplify3D, i forget what version though, i'll have to look. I only been using cura bcuz thats what I started with. I'll have to look into that slicer...
  12. Replies
    14
    Views
    13,377

    I want to improve strength. I'm not totally...

    I want to improve strength. I'm not totally concerned about look because currently when it goes back and forth from the pillar to that front leg (with the holes in it) I end up taking a razor blade...
  13. Replies
    14
    Views
    13,377

    i tried, i was looking to see if someone could...

    i tried, i was looking to see if someone could identify my specific issue based on the pictures. Like why the layers aren't blending like they should. Everything in that other thread you linked was...
  14. Replies
    14
    Views
    13,377

    Anyone have any suggestions please?

    Anyone have any suggestions please?
  15. Replies
    14
    Views
    13,377

    Looking for PETG Tip

    Monoprice Maker Select v2Temps = 150/7520 mm/s print speed (inital layer speed 8mm/s, only way I could get it to stick properly)Wall speeds 10 outter and 20 innerInfill 80% at 10 mm/sSo as you can...
  16. Replies
    10
    Views
    29,273

    So I figured out a way to get things to stick, I...

    So I figured out a way to get things to stick, I have glass with painters tape and polymide tape on that and the nozzle pretty close to the surface going at about 8mm/sec for the first layer and...
  17. Replies
    10
    Views
    29,273

    I'll give that a shot. Move the nozzle closer to...

    I'll give that a shot. Move the nozzle closer to the bed helped a little. I mean like to the point where its smashing it down into the bed lol. Its the only way I can get it to work. It still...
  18. Replies
    10
    Views
    29,273

    Thats the thing, my bed is level, i made sure of...

    Thats the thing, my bed is level, i made sure of it. Its the standard paper thin distance so that theres just a little resistance under the nozzle on it. Maybe i'll put it too close just to test how...
  19. Replies
    10
    Views
    29,273

    As I watch it, it seems like its curling up as it...

    As I watch it, it seems like its curling up as it hits the bed and then gets attached to the backside of the nozzle......whats causing this?
  20. Replies
    10
    Views
    29,273

    Need Help w/ PETG

    Someone please educate me on how I can make PETG stick. I'm using a Monoprice Maker Select v2 (Duplicator i3) with the stock bed lined with painters tape using hairspray. I've got a fresh nozzle,...
  21. Replies
    7
    Views
    4,562

    Oh no, Amazon Basic is the exact PETG i have!...

    Oh no, Amazon Basic is the exact PETG i have! lol, its translucent though not solid color. What Petg are you using that you've had success with? I've only used Amazon and Maker Greek stuff at this...
  22. Replies
    7
    Views
    4,562

    Yeah I cleaned out the nozzle when I was in there...

    Yeah I cleaned out the nozzle when I was in there as well, but I'd like some fresh one just because its good to have. I've only been using PLA as of now but I have a roll of PETG and ABS i plan to...
  23. Replies
    7
    Views
    4,562

    Thanks for the reply, yeah I got it dialed in a...

    Thanks for the reply, yeah I got it dialed in a little better with a re-leveling after replacing the PTFE tube, turns out it had been awhile. PTFE tube looked fine so i'm thinking the leveling helped...
  24. Replies
    7
    Views
    4,562

    Help with Monoprice Select v2

    I've been printing for the last year or so with no issues then the other day I started getting warping problems and on certain prints (with the same exact settings as my other items) it was not...
Results 1 to 24 of 24