Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Yea kind of. Most of the users I have helped...

    Yea kind of.

    Most of the users I have helped with Hictop controllers have asked me many times If I had a Pin-out for the Controller.
    Did not know of a better way of getting this information to...
  2. Hictop controller MPK_V1 pinout mapping

    The pin-out mapping is very similar to the Base v1.3 an MPX.3 they do not have a H6 connector


    You may note : two ICSP ports on controller. H6 is a standard ICSP header, but for programming the...
  3. Replies
    7
    Views
    338

    Where did you download the nozzle

    Where did you download the nozzle
  4. Replies
    5
    Views
    631

    I have upgraded to Marlin 2.0.6.1 an have enabled...

    I have upgraded to Marlin 2.0.6.1 an have enabled #define BABYSTEPPING this gives me the advantage on increasing the nozzle to that perfect height while printing a skirt.
    My proximity sensor is...
  5. Replies
    4
    Views
    4,516

    I suddenly remembered now had posted and went...

    I suddenly remembered now had posted and went back to a old post on a different forum and dug up this old post.




    Look at this example Black is Cura Blue is Prusa Slicer 2.3.0
    17250
    ...
  6. UMaine Composite Center 3D Printed a 2 ton boat...

    UMaine Composite Center 3D Printed a 2 ton boat here, here, looking at any 30 foot boat you would be printing forever
    on any of the 3D Printers you have mentioned.
  7. Replies
    9
    Views
    848

    Airkout Posting the Cura Profiles created and...

    Airkout

    Posting the Cura Profiles created and use daily to 3D Print using a .4 nozzle up to .32mm successfully.
    .32mm is max layer height at 80% of the nozzle diameter.

    Give them a try and see...
  8. Replies
    9
    Views
    848

    The creality slicer 4.8.2 slicer is one of the...

    The creality slicer 4.8.2 slicer is one of the oldest slicers out.

    In fact it is Cura 15.04.6 shown in the image below.

    17213

    I have Cura 15.04.6 and on occasion still use Cura 15.04.6...
  9. Replies
    9
    Views
    848

    In order to help you could help us by posting...

    In order to help you could help us by posting your Slicer and slicer settings.
  10. Replies
    9
    Views
    1,234

    Hello Krystyn13 You may be referring Hictop 3D...

    Hello Krystyn13

    You may be referring Hictop 3D Printers, I have a 3DP11 and 3DP12 both have been upgraded to what could be described as a 3DP18.

    These 3D Printers have been obsoleted are still...
  11. Replies
    4
    Views
    1,118

    Had a build surface that no matter what I did...

    Had a build surface that no matter what I did nothing would stick, believe it or not went to a cheap Chinese bed surface and most of my problems with filament not sticking are gone.
    This was...
  12. Replies
    2
    Views
    827

    Post photo with printed model + slicer with Model...

    Post photo with printed model + slicer with Model please.
  13. Wish I could help. I purchased my printers...

    Wish I could help.

    I purchased my printers both on E-Bay used, the first one showed up without assembly instructions.
    As they were used I expected some missing parts, so before purchasing these...
  14. Be careful and scan all downloads for viruses...

    Be careful and scan all downloads for viruses before executing.
  15. Most likely you need a Driver to allow the PC to...

    Most likely you need a Driver to allow the PC to talk to the Arduino driven 3D Printer.

    I use this driver CH34x_Install_Windows_v3_4.

    Do not remember where I downloaded, but I believe a...
  16. This was a removed from the rewriting of the core...

    This was a removed from the rewriting of the core components, from what I have read.


    However you can Use export to Octoprint
  17. I would reset your 3D Printer firmware memory to...

    I would reset your 3D Printer firmware memory to factory, an try again.

    Send :
    M502: Factory Reset - Marlin Firmware
    M500: Save Settings - Marlin Firmware
  18. Replies
    5
    Views
    999

    Power-Loss Recovery...

    Power-Loss Recovery This is something I have never done, one reason is because I have a pair of APC 2200 smart UPS's.
    However I found the above link which may prove helpful.

    Now I have not...
  19. Under Extrusion YES. Possible causes 1....

    Under Extrusion YES.
    Possible causes

    1. Teflon tube deformed / burnt.
    2. Slicer configuration error. "I did this somehow configured 3 mm filament when using 1.75mm filament.
    Photo Below. Fish...
  20. Replies
    3
    Views
    1,181

    Was just a thought.

    Was just a thought.
  21. Replies
    3
    Views
    1,181

    OK a Question? In what country were you in...

    OK a Question?

    In what country were you in before returning to the UK.

    Is there a different voltage between the two countries, maybe a different line frequency example 50hz vs 60hz.
  22. Replies
    3
    Views
    1,315

    This Item I would print like in attached photo....

    This Item I would print like in attached photo. support everywhere fill amount 30%

    16767

    Anything else.
  23. Replies
    5
    Views
    1,673

    It would help to know your slicers settings, and...

    It would help to know your slicers settings, and what 3D Printer you are using.
    Post Screen captures of the Display after slicing, Include the model showing model,
  24. Replies
    10
    Views
    4,969

    Post your configuration,h file for Marlin the...

    Post your configuration,h file for Marlin the version number.
    I will be look see what I can do.

    My end-stop / home config.


    // Mechanical endstop with COM to ground and NC to Signal uses...
  25. Many many year ago I started in the computer...

    Many many year ago I started in the computer industry, it seemed like every day a new company would startup.

    Many of these new company's never made it past the first couple of years, leaving a...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4