Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    257

    You can successfully 3D Print up to a 0.32mm...

    You can successfully 3D Print up to a 0.32mm layer height with a 0.4mm nozzle.

    max extrusion is about 80% of the nozzle diameter. 80% * .4 = .32
  2. Replies
    2
    Views
    118

    This could be the cables are mislabeled, this...

    This could be the cables are mislabeled, this happens once in a while.

    If you follow the cable from the controller to the stepper motor and from the end_stop switch to the correct location on the...
  3. I do not believe your printer is defective. ...

    I do not believe your printer is defective.

    Post your Cura profile.
    We are eliminating from point a - z
    Run Cura Click on Preferences then on the Profile set to print > Export Post this exported...
  4. Sliced with PusaSlicer 2.3.0 using modified Ender...

    Sliced with PusaSlicer 2.3.0 using modified Ender 3 Configuration as my Hictop3DP11/12 build area is not the same.

    15821
  5. We can post many models that you cannot print...

    We can post many models that you cannot print with the Creality Slicer ever, no mater how many years learning how to change the settings.
    Creality slicer is a copy of Ultimaker Cura 15.04.6, This...
  6. Replies
    16
    Views
    9,975

    These are a must for your Smooth rod support...

    These are a must for your Smooth rod support. printed these twice the first looks bad.

    This mount will make your 3D Printer easier to adjust Nozzle height. bed leveling will be more accurate.
  7. Post the STL for me.

    Post the STL for me.
  8. Post your Cura version number and settings...

    Post your Cura version number and settings profile.

    I will take a look.
  9. Replies
    7
    Views
    257

    When replacing the bowden tube you have to push...

    When replacing the bowden tube you have to push it in quite hard otherwise it will not reach the bottom, thereby forming a pocket that causes a clogs.
    You may need to burn out the nozzle, this can...
  10. Replies
    16
    Views
    9,975

    3DP11 Red is a 12 volt 3D Printer, while Blu is a...

    3DP11 Red is a 12 volt 3D Printer, while Blu is a 24volt 3D Printer.

    Red came with a Z-Axis end-stop manual switch, while Blu came with a Z-Axis inductive proximity sensor.
    Both have been...
  11. Replies
    16
    Views
    9,975

    The Board is an ATmega2560 it will use ...

    The Board is an ATmega2560 it will use

    #define MOTHERBOARD BOARD_MKS_BASE_14

    As it has 5 Stepper motor Drivers for use with X, Y, Z , E0 and E1


    3DP11 Red
    3DP12 Blu
    Believe me these are...
  12. Thread: Hello

    by Roberts_Clif
    Replies
    1
    Views
    179

    Hello; What 3D Printer do you have?

    Hello;

    What 3D Printer do you have?
  13. Most solid frame 3D Printers could print the...

    Most solid frame 3D Printers could print the charms.

    I would look away from any 3D Printer that in made with a plastic frame and look at those that have a rigid metal frame design.
  14. Replies
    11
    Views
    1,319

    We do not have any of these where I live but...

    We do not have any of these where I live but found this
    https://www.youtube.com/watch?v=GZpdDch2o4M
  15. Replies
    7
    Views
    750

    Learning the techniques of adding supports on...

    Learning the techniques of adding supports on complex models can take trial an error, there is not one setting that is a fix all for all models.

    My self have been learning the fine aspects of the...
  16. Never Heard of Just3DPrint in fact searched the...

    Never Heard of Just3DPrint in fact searched the Web an could not find them there either.
  17. Replies
    11
    Views
    1,319

    With an enclosure printing ABS at 232C with the...

    With an enclosure printing ABS at 232C with the bed set to 96C Have 3D Printer over 2 year now with these settings.
  18. Replies
    8
    Views
    2,769

    Thought I had killed a controller because I...

    Thought I had killed a controller because I flashed it incorrectly, though keep trying and finally brought it back to life.
  19. Plus One more who is to say they don't keep a...

    Plus One more who is to say they don't keep a copy of your Creations.
  20. Replies
    1
    Views
    386

    I had a similar problem rerouting the stepper...

    I had a similar problem rerouting the stepper cables away from the controller as quickly as possible and shielding the controller corrected.

    I used Aluminum foil Duct Tape on the inside of my 3D...
  21. Replies
    3
    Views
    425

    I do not change the nozzles very often though...

    I do not change the nozzles very often though when nozzles have to be changed they are in petty bad shape.

    Only the left most nozzle is good all others are not top somehow is enlarged bottom &...
  22. Replies
    10
    Views
    1,515

    PrusaSliscer with my Hictop 3DP11 an 3DP12 3D...

    PrusaSliscer with my Hictop 3DP11 an 3DP12 3D Printers.

    Here is the Finished Print. Artifacting almost non-existent.
    Printed in 3hurs 48 minutes

    15733
    Prusa 3MF attached
  23. Replies
    10
    Views
    1,515

    I am trying a Print with a modified layer...

    I am trying a Print with a modified layer thickness across the lower area to see how well this will change the terraces.

    The dark Blue layer height is .08mm the Green has a layer height of .2mm.
    ...
  24. Posted your comment on Prusa forum an hopefully...

    Posted your comment on Prusa forum an hopefully some will post a solution.


    an here is what the best had to say.
    "the Mk1 is largely the same as the Mk2, (except for mesh bed levelling) and...
  25. 1. Tetris 2. Super Mario 64 3. The Legend of...

    1. Tetris
    2. Super Mario 64
    3. The Legend of Zelda
    4. Doom
    5. Ms. Pac-Man
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4