Close



Dig deeper, search our News website




Search:

Type: Posts; User: airscapes

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    11
    Views
    850

    When PLA is exposed to moisture for too long it...

    When PLA is exposed to moisture for too long it gets brittle.. The roll is bad, if you can contact the manufacture they will probably replace it. All filament absorbs moisture and the results are...
  2. depends on the type of filament, but for PLA,...

    depends on the type of filament, but for PLA, store it in a ziplock or vacuum type bag (used to store cloths or blanks) when not in use. You should be fine while it is printing.
  3. looks like hardware to me.. filament type can not...

    looks like hardware to me.. filament type can not do that.. Only thing that is possible is if it was over extruding and the extruder hit the part during a move and become out of sync with the Gcode....
  4. Replies
    4
    Views
    2,121

    i guess the point I am trying to make is that...

    i guess the point I am trying to make is that wood Filament is only 30% wood at most.. and the process of adding it would be in a powder form that I expect is not being created by the filament maker...
  5. Replies
    4
    Views
    2,121

    Wood filament is only a small percentage wood.....

    Wood filament is only a small percentage wood.. it is plastic.. I have used wood filament, only one brand, and it was not very good.. I highly doubt that what you would want to do is going to be...
  6. Replies
    0
    Views
    1,341

    Another good company going belly up

    Hopefully someone will buy them and get things back on track.

    https://makergear.com/pages/due-to-severe-supply-chain-disruptions-read-the-following-before-ordering
  7. This would probably fit your needs...

    This would probably fit your needs https://ninjatek.com/shop/cheetah/
  8. Replies
    2
    Views
    643

    slow down, that cube is what 20mm square.. try...

    slow down, that cube is what 20mm square.. try 25mmS .. turn the temp up, try 230C. Jerk setting maybe to fast, may be over extruding try reducing the extrusion multiplier by 2. Please do not change...
  9. Replies
    7
    Views
    5,845

    What Bikeracer2020 was referring to is when you...

    What Bikeracer2020 was referring to is when you print your part as it is, that tab is standing up and the layers go across the width of the tab. If the tab was a separate part, it would be printed...
  10. Replies
    7
    Views
    5,845

    PETG should work for you

    PETG should work for you
  11. in your start script after the home of everything...

    in your start script after the home of everything but before the start of the gcode, put in an entry to move where you want it to be.
  12. Besides the slicer, if you want a more accurate...

    Besides the slicer, if you want a more accurate single wall, it needs to match that which the nozzle prints.. For instance a .4mm nozzle can much more accurately print a wall that is .45mm in width. ...
  13. Replies
    1
    Views
    729

    Looks like it is too hot.. now familiar with that...

    Looks like it is too hot.. now familiar with that brand of TPU but Ninjaflex looks like that when it is too hot..
  14. Replies
    1
    Views
    4,309

    I would think it will be fine. To be honest the...

    I would think it will be fine. To be honest the edges of the build plate normally suffer from not enough heat. Having the heater extend out past the edge would seem to be helpful to prevent uneven...
  15. Unfortunately this is normal for this price point...

    Unfortunately this is normal for this price point of machine. You can not have a high quality accurate machine for next to nothing... Start looking for a replacement glass plate that will fit, or...
  16. Replies
    3
    Views
    3,799

    why don't you just buy a quality machine that...

    why don't you just buy a quality machine that will work correctly out of the box and allow you to learn all the things you need to learn about designing components that will be 3d printed and...
  17. Replies
    2
    Views
    1,079

    Do you have the parts fan running starting with...

    Do you have the parts fan running starting with the second layer? Is it really PLA? Do you have another roll you know is good you can try? Sometimes thing get mislabeled, take the filament in your...
  18. Replies
    5
    Views
    1,789

    Double check your slicer and make sure you don't...

    Double check your slicer and make sure you don't have a negative value (making the nozzle closer) in the Z offset setting, assuming your slicer has that parameter. What happens if you let the part...
  19. Replies
    5
    Views
    1,789

    can't see anything with those tiny pics.. but if...

    can't see anything with those tiny pics.. but if you have what looks like waves with first layer.. nozzle probably too close to bed.. Ender machines are low quality toys.. good luck,you will need it...
  20. Replies
    11
    Views
    2,491

    Good luck!

    Good luck!
  21. Replies
    11
    Views
    2,491

    what every you do, stay away from Creality...

    what every you do, stay away from Creality products.. it is some of the worst junk out there..
  22. Replies
    11
    Views
    2,491

    some other things for inspiration

    some other things for inspiration
  23. Replies
    11
    Views
    2,491

    If you plan on leaning one of the CAD software...

    If you plan on leaning one of the CAD software programs so you can design you own parts for projects and repairs, you will want a quality machine, Prusa won't disappoint. If you want to print dodas...
  24. Replies
    11
    Views
    2,491

    Your head will hurt even more if you are not...

    Your head will hurt even more if you are not careful, you get what you pay for.. you will hate 3d printing with printer that does not work as is should. It is not plug and play it is a big ass...
  25. Replies
    6
    Views
    2,586

    Stake and 1/4 NC knob for spot light, screw in ...

    Stake and 1/4 NC knob for spot light, screw in mounting plate, bearing holder for flying bat. Buck regulator box with cover, buss terminal, gell holder, lamp hood.. all these I completed the other...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4