Close



Dig deeper, search our News website




Search:

Type: Posts; User: super7800

Search: Search took 0.00 seconds.

  1. yeah it just sketched me out abit too much, just...

    yeah it just sketched me out abit too much, just a little... off. like the about page talking about selling cell phone parts etc. i mighta gone for it if they accepted paypal but giving them direct...
  2. is stepper-store.com a safe website to buy stepper motors?

    i am wondering if stepper-store.com is a legitimate website that someone has actually bought from. the only reason i want to purchase from them is the free shipping. however, looking at their about...
  3. @autowiz I didnt mean to come off as an...

    @autowiz

    I didnt mean to come off as an arduino hater. I like arduino but prefer programming it in its native avr c or compiler personally. I know that "arduinos" are the heart of most 3d...
  4. I have to say I dont recommend an arduino for...

    I have to say I dont recommend an arduino for tempeture control to a electronics/ software beginner. I have personally witnessed arduino controlled heaters lock up and fry stuff. I would recommend...
  5. to add my opinion: the reason that the duets...

    to add my opinion:

    the reason that the duets are so expensive is the fact that they are essentially selling software and hardware together. modular is good, but when something starts off using the...
  6. Replies
    1
    Views
    1,667

    i don't know much about your specific printer,...

    i don't know much about your specific printer, but if your overhauling it why not update the control board also?

    skr 1.3 has a screen and is 32 bit. might be quieter also:...
  7. i'd go with keenovo. expensive but wont burn your...

    i'd go with keenovo. expensive but wont burn your house down.

    here is a controller (42usd)...
  8. Replies
    9
    Views
    8,272

    i bought the clone of the duet 2 and duex5 from...

    i bought the clone of the duet 2 and duex5 from aliexpress, from a company called fysetc, as i heard that the clones from them where of a higher quality. i would have bought the original gladly if it...
  9. if your looking for something to work, and work...

    if your looking for something to work, and work great i recommend the ultimaker printers. i've seen people go from never even seeing a 3d printer to making great prints in under a half hour, so very...
  10. Replies
    9
    Views
    8,272

    hello! it is currently 1/10/2020 and i figured id...

    hello! it is currently 1/10/2020 and i figured id post an update. the frame is almost finished (see below pictures), and i figure that if anyone here has any input on things i could improve, i should...
  11. Replies
    9
    Views
    8,272

    if anyone wants to follow the project further,...

    if anyone wants to follow the project further, here is a reddit post i made where people have been helping me out:...
  12. Replies
    9
    Views
    8,272

    i decided to go with the duet 2 ethernet and duex...

    i decided to go with the duet 2 ethernet and duex 5 for control, however i will buy cloned to save some money (its over half off buying cloned). has anyone had problems using cloned?

    the board...
  13. Replies
    9
    Views
    8,272

    thanks for the advice! looking at prints that...

    thanks for the advice!

    looking at prints that the kraken had done, i had noticed drips but had assumed that was due to it being setup incorrectly. thanks. however, i cannot do what you suggested...
  14. Replies
    9
    Views
    8,272

    DIY Large Scale 3D Printer Build Log

    Hello all. I am new to 3d printing (only used one maybe a dozen times) and do not own one, and would like to build my own. However, I have little knowledge on how they are designed. so using my...
Results 1 to 14 of 14