Close



Dig deeper, search our News website




Search:

Type: Posts; User: Roberts_Clif

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds; generated 46 minute(s) ago.

  1. Thread: Mpcnc

    by Roberts_Clif
    Replies
    24
    Views
    1,959

    1st Print on my MPCNC was a simple pen sketch of...

    1st Print on my MPCNC was a simple pen sketch of a Crown

    13148


    MPCNC (508mm X 762mm X 292mm)
    13150
  2. Replies
    5
    Views
    734

    What temperature would you print ABS.

    What temperature would you print ABS.
  3. Replies
    2
    Views
    227

    Can not find attached photos

    Can not find attached photos
  4. Replies
    6
    Views
    506

    I have very little to go on, you have provide the...

    I have very little to go on, you have provide the forum with only of a photo showing under-extrusion.
    Then Stated "PLA 1.75mm"

    If you would provide more information, it could make it much easier...
  5. Replies
    6
    Views
    506

    Do you have an all metal hot-end or do you have a...

    Do you have an all metal hot-end or do you have a Teflon tube in the throat.

    If you have a Teflon tube you may want to disassemble the hot-end to see if the Teflon tube has deformed.
  6. As most thermisters are 100k at room temp I would...

    As most thermisters are 100k at room temp I would measure your thermister at room temp
    Below is my 100K Thermister Chart.

    See attached chart
    ...
  7. It sounds like you could have the bed and hot-end...

    It sounds like you could have the bed and hot-end connectors reversed.

    Check the the wring and make sure the wires calves are labeled correctly
  8. Replies
    6
    Views
    506

    It appears it could under-extruded What...

    It appears it could under-extruded

    What material are you trying to 3D Print.
  9. Thread: Mpcnc

    by Roberts_Clif
    Replies
    24
    Views
    1,959

    I can choose between Marlin and grbl for Cyclone....

    I can choose between Marlin and grbl for Cyclone. I just testing my Controller with Marlin will see about testing grblForCyclone real soon.

    Today I received the five steppers motors, and setup a...
  10. Thread: Mpcnc

    by Roberts_Clif
    Replies
    24
    Views
    1,959

    Today received the Arduino controller the Ramps...

    Today received the Arduino controller the Ramps 1.6 with five A4988 drivers modules.
    Decided to upload a known Firmware Marlin 1.1.5 to test the the basics, found that I needed a CH34X driver...
  11. Thread: Mpcnc

    by Roberts_Clif
    Replies
    24
    Views
    1,959

    The build is going quite slowly, simply because...

    The build is going quite slowly, simply because when I started this project, was hoping to use some of my spare 3D Printers parts.
    This scenario is quickly proving not to be the case with the MPCNC...
  12. Replies
    5
    Views
    734

    Exactly! This is what I am saying I can not...

    Exactly!

    This is what I am saying I can not tell you why it prints so well with a Nozzle temp of 228C an the Hotbed temp of 96C.
    Other than it is working inside an enclosure the heat inside...
  13. Replies
    5
    Views
    734

    I print PLA at 198C. Maybe Temps are off,...

    I print PLA at 198C.

    Maybe Temps are off, though I have measured with an external Multi-meter temperature probe an Printer matched Multi-meter.

    Have printed a ABS temp tower looked best at 228...
  14. Replies
    5
    Views
    734

    1st ABS Failed Print

    Today I had my first failed ABS print.
    Although it was defiantly my fault, was still a my first failed ABS Print, now this was a simple error on my part.
    As I was in a hurry to print the model I...
  15. It is good you diagnosed the problem, post a...

    It is good you diagnosed the problem, post a photo lets us see this design.
  16. Looked at you Configuration.h file See no reason...

    Looked at you Configuration.h file See no reason for no movement.
    can you do a test on the end-stops using M119 test each end-stop in the normal position then again with manually Pressed End-Stop
    ...
  17. Would need to see your Configuration.h file. You...

    Would need to see your Configuration.h file.
    You can post it to a share like Google Drive and post a link.
  18. Replies
    5
    Views
    510

    I should stick to the one I do. Preferred...

    I should stick to the one I do.

    Preferred method
    Using a terminal that can send G-Code.
    M502 reverts to the default "factory settings". You still need to store them in EEPROM
    M500 ...
  19. Replies
    5
    Views
    510

    When Flashing firmware one step is alluded, YOu...

    When Flashing firmware one step is alluded, YOu need to restore the Firmware defaults settings.

    This can be accomplished in a couple ways.

    First Way.
    Using a terminal that can send G-Code....
  20. Replies
    1
    Views
    289

    Will post the link for you....

    Will post the link for you. https://pastebin.com/xqfeksNK

    Wish I had an answer though do not know...

    I do know that on my machine I have to start the fan above about 42% fan speed or about...
  21. Replies
    57
    Views
    7,029

    Where did you get the articulating Dragonfly

    Where did you get the articulating Dragonfly
  22. Thread: Mpcnc

    by Roberts_Clif
    Replies
    24
    Views
    1,959

    Found a problem with the MPCNC Design. 13004 ...

    Found a problem with the MPCNC Design.

    13004



    You can see in the middle assembly, that the 5/16 bolt head and the Bearing are touching, This will have to have thinner Bolt...
  23. There are many things that could cause the...

    There are many things that could cause the problems you are experiencing.
    Slicer and 3DPrinter setting conflicting, Hot-end temperature incorrect for filament, printing too fast, 3DPrinter not...
  24. Thread: Mpcnc

    by Roberts_Clif
    Replies
    24
    Views
    1,959

    Assembled the Middle Assembly today still need...

    Assembled the Middle Assembly today still need the conduit to assembly the remaining frame Assemblies.

    12987
  25. Thread: Mpcnc

    by Roberts_Clif
    Replies
    24
    Views
    1,959

    I have never calculated it only took the numbers...

    I have never calculated it only took the numbers from Cura do you have a formula

    Found this V=pi*radius^2*print speed = mm3/s.
Results 1 to 25 of 495
Page 1 of 20 1 2 3 4