Close
Flash Forge Guider



Dig deeper, search our News website




Search:

Type: Posts; User: hdtvjeff

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    750

    The underside of that pulley is solid; so I...

    The underside of that pulley is solid; so I gather the side you are seeing can be solid too!
  2. Replies
    10
    Views
    750

    The pulley in question needs the edges on both...

    The pulley in question needs the edges on both sides to keep the belt in place; guess it was the way Panasonic engineers designed it.
  3. Replies
    10
    Views
    750

    Thank you Fred, I was curious too, with a good...

    Thank you Fred,

    I was curious too, with a good 3d printer at home could it be done at home with the right filament and knowledge or are finely detailed prints best left to outside sources ?
  4. Replies
    10
    Views
    750

    Printing of a Tiny Pulley Question

    Hello again,

    Attached you will see a half inch pulley from a Panasonic Cassette deck,

    I need a copy of this pulley but with a slightly larger diameter with the other measurements staying the...
  5. Replies
    20
    Views
    1,952

    Thank you so much for the thorough explanation !

    Thank you so much for the thorough explanation !
  6. Replies
    20
    Views
    1,952

    Fred and Ralph, Thank You !

    Fred and Ralph, Thank You !
  7. Replies
    20
    Views
    1,952

    As a follow up I have to ask this.I have a...

    As a follow up I have to ask this.I have a cassette lid from my stereo, not sure if it is plastic or acrylic but is it at all possible to 3d print clear see thru complete with the lock tabs seen in...
  8. Replies
    20
    Views
    1,952

    Thank you Fred for the valuable insight I can...

    Thank you Fred for the valuable insight
    I can only imagine what we will be 3d printing 10 years from now.

    I remember starting with a panasonic dot matrix monochrome printer thrilled to print out...
  9. Replies
    20
    Views
    1,952

    Thank you for that wonderful advice Fred Just...

    Thank you for that wonderful advice Fred

    Just curious, asides from a pulley with the right skill set and software can metal parts that make up a older audio cassette deck be replicated too?
    ...
  10. Replies
    20
    Views
    1,952

    That looks like programming; is using a 3d...

    That looks like programming; is using a 3d scanner easier in that respect?
  11. Replies
    20
    Views
    1,952

    Wow! Are you saying I can make those pulleys...

    Wow!

    Are you saying I can make those pulleys without a scanner if I master the methods you mentioned?

    Does a digital caliper take into account slight curves and rounded corners too?

    As a...
  12. Replies
    20
    Views
    1,952

    This is the printer I just got, have not even...

    This is the printer I just got, have not even unboxed it yet; just looking for your recommendation for a scanner
  13. Replies
    20
    Views
    1,952

    Thank you, Would the quality be good? Also, can...

    Thank you, Would the quality be good? Also, can you recommend a scanner (affordable) to scan parts like these?
  14. Replies
    20
    Views
    1,952

    Can a 3d printer make this part?

    hi,

    Please look at the photo, there are two plastic pulleys from a 45 year old cassette deck.

    Can a 3d printer make those pulleys?

    Thanks !
  15. Replies
    4
    Views
    606

    3d PCB printing?

    Hi everyone,

    Hope this is the right forum

    I need to recreate a 4 inch by 3 inch printed circuit board from a Panasonic audio cassette deck.

    Can 3d printing accomplish this?

    I just bought...
  16. Replies
    10
    Views
    2,256

    Thank you Andrew for the thorough response.

    Thank you Andrew for the thorough response.
  17. Replies
    10
    Views
    2,256

    Can these parts be made by a 3d printer?

    Hi,

    If I have not posted in the correct place, excuse me.

    Before I invest in a 3d printer and scanner I thought Ishould ask here first.

    My sole purpose will be to replicate parts for...
  18. Replies
    11
    Views
    2,673

    Can you upload sample cassette mechanism parts...

    Can you upload sample cassette mechanism parts you have replicated and their original?

    Jeff
  19. Replies
    11
    Views
    2,673

    Wow Geoff, That is amazing, the chassis I can...

    Wow Geoff,

    That is amazing, the chassis I can replicate too? With all the openings, contours, front back top and bottom too?

    I am realizing I need a scanner and the 3d printer, two separate...
  20. Replies
    11
    Views
    2,673

    Here is a an exploded view of the cassette...

    Here is a an exploded view of the cassette mechanism, and thank you for answering my question.2901290129012901
  21. Replies
    11
    Views
    2,673

    Can a 3D printer do this question

    Just discovered this wonderful forum.

    I collect vintage cassette decks from the 1970's

    It is next to impossible to get parts for knobs, gears, pulleys etc.

    I do have original parts of my...
Results 1 to 21 of 22