Search:

Just got into printing and so far pretty impressed with my Ender 3 Pro. My slicer is Simplify3D, using Ender 3 Pro profile and default PLA profile. PLA is grey eSun PLA+. Only settings I've changed...

How often does one have to level the bed? Does it retain the calibration after a power cycle?

If someone could tell me how to edit the config file I posted to get manual BL enabled that would be great.

I have no idea how to transfer the relevant settings to a machine-agnostic firmware. I just want this thing to work with what is supplied. I haven't gotten far enough to know if I have a "lumpy"...

From the config it looks like Manual BL uses Mesh BL?

BTW if anyone can tell me in Cura where to set the Z offset I'd appreciate it!

We haven't wired the BL Touch because we don't have the mount printed. Haven't even looked at the instructions, but from your comment it takes the place of the Z probe? That makes sense why it...

I tried enabling Manual Bed Leveling and disabling ABL in the configuration.h file, but the printer behaved exactly the same: jumped through 9 positions on its own and stopped. The .h file compiled...

Do you know of a good walkthrough?



I don't understand what your saying here?

Thanks for the help!

Gotta say I'm pretty pi$$ed off at the moment with this printer. Had the ACME rod mounts printed commercially and installed them. First off, the alignment sucks, had the steppers binding up near the...

It's the LCD from Makerfarm. I personally don't think it's the format, or the cables. I think needs to send us a new LCD, unless you guys know of any other reasons?

But first we have to print the mounts for the ACME rods with funky settings, a Catch-22. We're just going to have the rod mounts printed for us this week and swap to the ACME rods this weekend and be...

We did get the upgrade at the same time, but haven't done any of the upgrades as most require printing something.

what file is that in?

So spinning that knob from 4000 to 8000 is a waste oof time. I assume this value is in one of the .h files? So I should just edit it there, recompile with the arduino software, and upload to marlin?...

So looking at my stepper drivers the one driving the Z steppers is different than the rest, with no black chip. Can't be a coincidence. Wonder if Colin ran out and got some of these but it is a...

I believe the firmware we loaded was Marlin1_0_2_Pegasus12.ino. Just manually moving the Z axis just now and it shows a position of 220 while it is actually about half way to the top. So it does...

So where is the origin? I assume this where home is? If I go into Prepare and manually move an axis, is the 0 position the origin? So if both X and Y show 0 I should be at origin? The reason I ask is...

So we've built the machine, did a crude manual bed level and the first print was quite good! It was a 1" cube, but somehow printed only 1/2" in height. I'm searching Slic3r, and the software (can't...

So my buddy bought the Pegasus and we're in the middle of the build! Couple questions:
1) why use the springs on teh heat bed? Does the underside of the heat bed need insulation for the heat bed...

Looking to make the order, upgrade kit is out of stock. How important are the ACME upgrade screws?

I thought the Deluxe upgrade kit used polycarbonate, but it is actually acrylic. And the kit is back in stock just moments ago!

The polycarbonate was referring to the sheets to enclose the printer, probably from Home Depot since the deluxe upgrade kit is currently unavailable.

Any particular hairspray?

Your LED is...

So, starting accessories...I have a wide variety of tools, but is there anything specific to 3D printing I should get?

Going to use PETG and PLA/PHA hybrids to start, what bed release?

Glass...

So a different motor comes with the Titan? It cannot use the stock Nema 17? (is too much torque a problem?) Also weight was mentioned, is this an issue? Is the Titan w/ lower weight motor desirable...