Close
Flash Forge Guider



Dig deeper, search our News website




Search:

Type: Posts; User: Access3Dservices

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    2,480

    Most 3D printers (including all of ours) have the...

    Most 3D printers (including all of ours) have the Z-axis limit switch at Z-min, meaning when the bed hits the switch the nozzle is in contact with the bed. The Z-axis travel range then tells the...
  2. I'm the Operations Director at a nonprofit that...

    I'm the Operations Director at a nonprofit that provides free services to people with disabilities. In response to repeated cuts to our State funding my boss proposed we start a 3D printing, 3D...
  3. Replies
    15
    Views
    2,480

    When you moved the endstop down did you increase...

    When you moved the endstop down did you increase the Z-axis maximum travel length? If not that would explain the printing above the bed, the bed can't reach the nozzle because it's outside the...
  4. With the older Flashforge firmware you can heat...

    With the older Flashforge firmware you can heat up to 260, but there's also custom builds that go higher. We've had great results printing Polycarbonate at 260, just don't try to push speeds too...
  5. We have two Flashforge Dreamers, they are fairly...

    We have two Flashforge Dreamers, they are fairly small volume but can print up to 240°C stock with a heated bed and fully enclosed. Equipped with WiFi and dual extruders, we paid $1k/ea two years...
  6. I'm about to start my first build, Hypercube...

    I'm about to start my first build, Hypercube Evolution with a 400mm x 400mm x 400mm build volume, BOM of cheap Chinese parts was $625 shipped plus about a spool worth of PETG printed parts required...
  7. Replies
    3
    Views
    1,874

    Today I went into the Repetier Online...

    Today I went into the Repetier Online Configuration Tool to grab the necessary values to change in EEPROM when I noticed I was using the tool version 0.91 but 0.92 was installed on the machine...
  8. Larger Nozzles on Flashforge Dreamer

    We recently upgraded our two Flashforge Dreamers with Micro Swiss All Metal Hotends and have been getting great results from it, even printing in Polycarbonate with the tiny 0.2mm nozzles! We've...
  9. Replies
    3
    Views
    1,874

    I'm not at the computer which had the compiling...

    I'm not at the computer which had the compiling issue but I copied the settings from the firmware provided by Cultivate3D into the Repetier Online Firmware Configuration Tool then changed the number...
  10. Replies
    3
    Views
    1,874

    Updating Firmware via Repetier-Host

    Hello everyone! An engineer friend of our organization recently finished building us a Cultivate3D Beast which is a large volume FDM printer. Our Engineer built it according to the manual which...
  11. Replies
    3
    Views
    820

    Hello Jerry and welcome to the forum from a...

    Hello Jerry and welcome to the forum from a fellow newcomer!

    -Joe, Access 3D Services
  12. News Hello everyone, just a quick update regarding the...

    Hello everyone, just a quick update regarding the Increasing Independence for People with Disabilities 3D Design Contest sponsored by Access 3D Services:

    Our Board of Directors has decided to...
  13. News 3D Design Contest, Win a Makerbot Replicator+ 3D Printer!

    10400

    Access 3D Services is hosting an Increasing Independence for People with Disabilities 3D Design Contest from April 1, 2017 to May 31, 2017. All designs must be the original idea of the...
  14. News Win a Free Makerbot Replicator+ 3D Printer!

    10397

    Access 3D Services is hosting an Increasing Independence for People with Disabilities 3D Design Contest from April 1, 2017 to May 31, 2017. All designs must be the original idea of the...
Results 1 to 14 of 16