Anuvin's Print Journal and How To Megapost

Hey there fellow backers, I decided I needed a place to post my prints and How to videos so they didn't end up all over the place. Let's start with build videos:


Unboxing the V1 kit:
https://www.youtube.com/watch?v=03WvT7XyjcA

Building the V1 printer:
https://www.youtube.com/watch?v=puIcRd61_Lk

Building the standard drip system (highly recommended):
https://www.youtube.com/watch?v=dNUMdVsyNMQ

So far, I am very pleased with how the peachy performs. It clearly has the capability to print highly detailed objects that would be nearly impossible for an FDM printer. Here is my first batch of prints from the peachy:


http://i.imgur.com/kFxO2Kcl.jpg

http://i.imgur.com/iMqEYSOl.jpg

http://i.imgur.com/0ejnh1Vl.jpg

http://i.imgur.com/7fEMqH4l.jpg

http://i.imgur.com/P9581J4l.jpg

I have also done a few print not from the print library, but I have just begun to play with the settings, so these prints are going to be much rougher for a while until I get Gcode figured out:

1 cm cube (it is 1 cm high, but only 7 mm wide)
http://i.imgur.com/Inoo5iAl.jpg

d20 (lopsided, numbers didn't come through strongly, but perfectly full and no holes or problems otherwise, too big attempt to the right)
http://i.imgur.com/DbJOalul.jpg

I will be updating this thread as I print and film more peachy stuff, and I hope I can help with build questions for people who used my videos to build their peachy.

Wow what a great post!
You have done so much in just the first few days! Thankyou so much, Im sure thousands of people will benefit from your videos dew time.

Thanks Rylan! I wanted to try something simple and fun, so I tried a grumpy t-rex.
Model : http://www.thingiverse.com/thing:637786


http://i.imgur.com/DWwysgGl.jpg
http://i.imgur.com/H6Rr2Upl.jpg
http://i.imgur.com/3e9nyvFl.jpg
http://i.imgur.com/67lNxV1l.jpg?1

Anuvin

Great prints. When I am up and running, I am going to try floating a thin layer of tap water on top of the resin. I have a theory that this might improve the layering..

Have you got any videos of the prints?

Anuvin, that's just awesome !
What is your overall impression about the quality of these prints, and the "Peachy Printer experience" in general ?

Quote:

---

Originally Posted by Anuvin

Thanks Rylan! I wanted to try something simple and fun, so I tried a grumpy t-rex.
Model : http://www.thingiverse.com/thing:637786


http://i.imgur.com/DWwysgGl.jpg
http://i.imgur.com/H6Rr2Upl.jpg
http://i.imgur.com/3e9nyvFl.jpg
http://i.imgur.com/67lNxV1l.jpg?1

---

That's really awesome, I'm excited to see other's print with this thing.

Quote:

---

Originally Posted by mike_biddell

Anuvin

Great prints. When I am up and running, I am going to try floating a thin layer of tap water on top of the resin. I have a theory that this might improve the layering..

---

I've also found the new MakerJuice resins specifically the Snap Fit drastically increases the smoothness of the prints.

Hi Anuvin.

Have you been doing any more prints lately? Anything you can share with the group?

/Martin

For the 10 or so people out there that have V1 peachy printer kits This is a great Thread to refer to when building your printer.
Anuvin was the first to build and print with a V1 kit, and he did an excellent job in documenting the process!