Can I make several identical prints in the same run?

My Ender 3 V2 is making a small box right now, 10 cm long (4") by 5 cm wide (2"). How would I proceed if I wanted to print say four of these at once please? Does openSCAD let me lay out one or more duplicates and arrange them so that they fit within the 22cm x 22cm base area?

Obviously the 5 hours or so I expect the single unit to take would become 20 hours, but I'd be comfortable leaving it unattended and avoiding the additional 'setting up' stages.

Terry, UK

you can actually use the slicer to print more htan one thing at a time.

so 100mm by 50mm - and it's taking 5 hours !
What speed and layer height are you using ?
That's ridiculous - even for an ender 3 - I mean I know they are slow - but damn, that's positively glacial !

But basically the slicer will not only generate duplicates for you, it will also lay them out on the bed.
Are you using cura or prusa slicer ?
prusa slicer is better :-)

In Cura, right click the object and choose "Multiply selected model.

Thanks, I'll try that shortly. Presumably if the result wouldn't fit on my Ender 3 V2 (220 x 220 x 250) then I'd be warned?

Quote:

---

Originally Posted by curious aardvark

you can actually use the slicer to print more htan one thing at a time.

so 100mm by 50mm - and it's taking 5 hours !
What speed and layer height are you using ?
That's ridiculous - even for an ender 3 - I mean I know they are slow - but damn, that's positively glacial !

But basically the slicer will not only generate duplicates for you, it will also lay them out on the bed.
Are you using cura or prusa slicer ?
prusa slicer is better :-)

---

Not sure about speed and layer height. I used defaults. Powering up the the Ender 3 V2 monitor shows these settings.


Attachment 16085

X axis speed = 500? Presume that means 50cm / sec, which seems very high? I measured about 3s to move 200mm using the monitor

What profile in the slicer are you using? Standard ought to be fine.
Scad creates the .stl file. Load that into the slicer (Cura) and copy the item there.

This is my Rep Rap Protos V3 with Simplify 3D slicer settings , I think you need to change up a gear or two on your printer ! Good luck Attachment 16099 And yes you can print as many parts as will fit on you printing bed ,as I use Simplify 3D no problem , but speed it all up or you will be months on one project !!

Thanks, but I couldn't read the text in your low res screenshot.

Quote:

---

Originally Posted by Axl_Myk

What profile in the slicer are you using? Standard ought to be fine.
Scad creates the .stl file. Load that into the slicer (Cura) and copy the item there.

---

For this (my first print) I used Creality Slicer. There was no option to choose Ender 3 V2 so I used 'Ender—3/Ender-3Pro/Ender-3-3S'. I used all other settings defaults.


Attachment 16101

https://www.dropbox.com/s/piewvtmasm...mate.jpg?raw=1

As you see, its print time estimate proved wildly high.

But as some others have said 3h22m was far too long, please advise what settings I should change?

I've had recommendations to use Ultimaker Cura instead, which I've now installed. At first sight I see no significant difference. It too has no setting for V2. And its estimate was almost identical (over twice as long as the actual print).

Attachment 16102

https://www.dropbox.com/s/upz76wywu6...mate.jpg?raw=1



If anyone else has printed this box, with similar dimensions to mine (10 x 5 x 4 cm), what was the print time?

Attachment 16103


https://www.dropbox.com/s/0lyoaps8ni...gLid.jpg?raw=1


EDIT:
All three images are OK here in Preview, but when I opened after sending they had all been replace with 'Attachment 16101', etc, and a message said Invalid.

I've just sent again and it's still the same.

So I've now added links instead.

Can I get some feedback please?


Terry

Quote:

---

Originally Posted by terrypin

Thanks, I'll try that shortly. Presumably if the result wouldn't fit on my Ender 3 V2 (220 x 220 x 250) then I'd be warned?

---

Cura, bottom left of screen shows object name and size. You can +/- the size in %. With object selected, left side screen. Second lab flask down, (that's what I think they are) check uniform scaling, and change 1 of xyz size.

Select your Cura config in the top right of screen for the dropdown. It will say Profile: Standard Quality. Click that, then on the down arrow. Try low quality.
Scroll through the settings. Check the temps. I change the print temps to 215º and 60º.
This is where all your slicer settings are. You can create and name special configs for different projects.
Have fun

Thanks a bunch, I'll take a close look at those settings in the morning. And maybe make a new config. Is that what I should do in the absence of an Ender 3 V2 option?

Did you see my screenshots OK?

I saw your pics ok. I made the same box for my deep well mm sockets a while ago using a LQ config.

there are no practical differences between the ender versions.
the mk2 uses a cheaper and less solid frame and - I believe - cheaper, but newer, control board.

But they've done nothing to improve speed - so you'll still need to keep it fairly slow.

Thanks, will experiment along those lines.OT question: when replying to posts the only option I see is ‘reply with quote’.Is that the case for all, implying that quote has to be deleted if not needed?

just use the quick reply box.
Attachment 16137

You won't have the moderator options - but you should have the rest.

After right clicking ; click on multiple model set to get that.

Yes you can do it