Hey! Would be cool to see how your prints have turned out, especially if you've used non new matter store stl-files and / or used some other filament than the new matter one.
So for the few of you that have received your printers - Please share ;)
Printable View
Hey! Would be cool to see how your prints have turned out, especially if you've used non new matter store stl-files and / or used some other filament than the new matter one.
So for the few of you that have received your printers - Please share ;)
Printed this Frankenstein light switch plate...
http://www.thingiverse.com/thing:649284
Printed with Inland silver PLA from MicroCenter.
Spool fits well on the holder and turns easily. Same size as sample Mew Matter Roll, except deeper (1kg)
I printed this by uploading the STL to my library, so it used all New Matter settings. Temp was fine.
I have also printed by uploading GCode from Cura through the desktop utility. Some models I have are support free, and the New Matter slicer added support in the middle of parts that don't need it, making holes for attaching pins difficult to clean.
I am very happy so far.
1st pic no flash, second pic flash.
Attachment 7628
Attachment 7629
great print - not sure how that is 'silver' though ?
The Inland "silver" is pretty much a grey. Hatchbox silver PLA is a bit darker, and more silvery.
I didn't do any post processing Came off the printer like that. It did have support under the plate, as there is a recess in the middle over the switch, so I removed those, but thats it. I did have to glue back one of the small prongs that broke while removing it from the bed. But that is probably a PLA thing, more than a printer thing. More brittle, and parts made vertically will always be weaker due to the layers.
New Matter posted some settings in their FAQs on the website.
http://support.newmatter.com/
Basic machine settings to set up the right machine, and Start/End code to add (theres a tab in Cura for that) that adds the same calibration as New Matter software.
Here is a test part I made to see if the printer could print to its claimed envelope (150mm x 100mm x 125mm).
https://instagram.com/p/8jnVnjLG2_/
looks pretty good.
The prints definitely can use some tuning. The overall surface quality is kind of like felt.
Attachment 7674
I started making some cookie cutters for my friend.
Attachment 7677
James-Its probably being caused by overheating the print. either lower the ambient room temp or reduce hotend/heatbed temp.
I finally got my printer the other day, here's my first "make" on thingiverse: http://www.thingiverse.com/make:174245
https://thingiverse-production-new.s...w_featured.jpg
Details in the post there. Now attempting a bigger print using high detail from astroprint, 14 hrs in looking great - but sloooooow ;)
The last object I printed was a Spooky Jack o Lantern for the last Halloween season! Here it is!
Attachment 7954
Here are a couple of prints, the first one just showcasing the difference between slicer settings, the good one is based off of AstroPrint's best settings but with reduced bottom and top layer heights and 100% infill. I made the model myself.
Attachment 8018
Here's a bigger print I did, using the astroprint best settings but reduced infill due to the large size. Since I've been experiencing the shifting issue with taller prints I opted to print this one lying down with lots of support.
In hindsight I should've printed it lying down at 90 degrees, instead I rotated it to have as little support as possible. This lead to severe striations in the bottom plate.
Should be noted that one of the supports fell over during printing, making the right hand messed up, you can't see it here but the back is messed up. It looked like cotton candy out of the printer but I heated a butter knife and flattened it, it's passable now.
This is my first big print and the first one I post process. I'm printing some sanding tools now. But sanded and applied gesso for a couple of rounds and then spray painted two layers. The glasses are removable and painted with matt acrylic and then sprayed with glossy veneer. Model based off of: http://www.thingiverse.com/thing:1057389
Before and after:
Attachment 8020Attachment 8019
A quick view of my prints
Attachment 8032
Here is my first print of my own stl object. I sliced it using Cura. Very nice!
The finished object without flash
Attachment 8190
The finished object with flash (layers are more visible than with human eyes)
Attachment 8188
The object with support structure and adhesion platform done by Cura.
Attachment 8189
A bolt with the screw from Thingiverse: http://www.thingiverse.com/make:182077
Attachment 8368
A whistle from Thingiverse (no sound :(): http://www.thingiverse.com/make:186249
Attachment 8369
A handle designed by me and sliced with Cura, the hooking was measured with a digital caliper and designed with 0.2mm margin: works perfectly!!!)
Attachment 8370Attachment 8371
I have another model done in 3 parts that interlocks and is really beautiful but I cannot post as it's top secret for now... ;)
I've bought quite a few samples of different "special" filaments to try out. First up is Laywoo-D3, a wooden filament.
To use the samples I first printed a sample spool based off of a design from thingiverse but with a custom inner ring (and just a small size difference in the arms), printed in newmatter pink. Works well enough, arms are detachable, a small problem with filament not being wound hard enough and sort of sliding out, I've seen other designs that might be better in this regard, but for now I'm sticking to this one. If anyone is interested I might stick it up on thingiverse (or even try to get it into the newmatter store?)
http://i.imgur.com/0Lgn87P.jpg
First print with special filament: the classic Le Fab Shop elephant. Printed without support, a 1 mm shell and with 0 infill to make the sample last (and it just barely did), sliced with astroprint, printed at 200 degrees (can be printed at different temperatures to change the colour of the wood). Feels very much like some sort of wood/paper. Very easily sanded, here I've just removed excess filament no major sanding and as you can see there are a few small artefacts. Lines are not that noticeable, and when they are they actually add to the wooden look!
http://i.imgur.com/f8d3l1q.jpg
http://i.imgur.com/Z1QbTbP.jpg
http://i.imgur.com/VlajJUO.jpg
sure how that is 'silver' though ?
not bad - do the elephants legs move ? that's the best test of a clean print :-)
Those woody filaments are quite good. just be aware that the ones with fairly large wood particles - like you have - are absolute bastards for clogging and blocking up printer nozzles.