- Tab Content
- terrypin's Activity
- About Me
-
Older Activity
-
04-12-2021, 05:04 PMWe must have our lines crossed somewhere. Could you try it one more time then, as you’ve lost me! Earlier you said you’d never used ‘it’. By...7 replies | 765 view(s)
-
04-12-2021, 04:37 PMThanks CA, good stuff there that I’m looking forward to trying out.15 replies | 983 view(s)
-
04-12-2021, 06:57 AMHi Brian, I'm a beginner too, but your post caught my eye. Firstly, that assembly looks rather easier than my Ender 3 V2 was about six weeks ago;...7 replies | 643 view(s)
-
04-12-2021, 06:17 AMThanks CA. I'm learning by the hour about each of the three main areas of my workflow: OpenSCAD, Cura and Ender 3 V2. One particular aspect of the...15 replies | 983 view(s)
-
04-07-2021, 12:39 PM"Your homework - make the box parametric :-)" $fn=50; // Defining the box ExteriorL=100; // Exterior cube, length ExteriorW=40; // Exterior...15 replies | 983 view(s)
-
04-07-2021, 10:10 AMNeat! Do you have a photo of it in use?15 replies | 983 view(s)
-
04-06-2021, 04:50 PMThanks CA. I managed to cleanly remove the main Cura support around the rim. But not the much smaller support underneath the little pull tag on top,...15 replies | 983 view(s)
-
04-06-2021, 12:20 PMHi Gambo: Thanks, you were quick off the mark! I realised my mistake shortly after posting and deleted the post ;-)26 replies | 1232 view(s)
-
04-06-2021, 12:10 PMIf you're asking about how to make sure the bottom of your lid will end up right at z=0 on your print bed, there's no issue. Yep, that was it. I...15 replies | 983 view(s)
-
04-06-2021, 06:18 AM"So you reckon it doesn;t always work ?" Do you mean OpenScad Customizer? If so: That works consistently for me, but has the limitation I...7 replies | 765 view(s)
-
04-06-2021, 05:49 AMThanks a bunch Kevin, great post! Particularly for that advice about facets. I actually tried to get a deliberately low facet value for the little...15 replies | 983 view(s)
-
04-05-2021, 01:45 PMCA: I’m not sure why thingiverse is relevant here, given that my post was about OpenScad’s Customizer?I had a few failures with the thingiverse...7 replies | 765 view(s)
-
04-05-2021, 08:23 AMI learned elsewhere that A1: Cura was correct to add support (although it was far more substantial than i'd expected). A2: My code was OK but...15 replies | 983 view(s)
-
04-05-2021, 08:02 AMThanks Gambo. ‘Layer height’ I understand! But I must read up further to grasp other terms I’ve encountered like ‘wall count’, ‘number of...26 replies | 1232 view(s)
-
04-04-2021, 01:42 PMHope my screenshot clearly explains my query: Q1: Is it therefore down entirely to the user to decide on that option? Q2: I'd also...15 replies | 983 view(s)
-
04-04-2021, 10:15 AMMany thanks Fritz. Yes, that's the part I'm particularly interested in. From CA's sentence: "if you increase horizontal perimeters in the slicer. it...26 replies | 1232 view(s)
-
04-04-2021, 06:26 AMSee resultant conclusions following my cross-post to the openscad sub-forum in reddit:...7 replies | 765 view(s)
-
04-04-2021, 03:15 AMCA, I’m interested in this too so would appreciate some detail of how you do that in Cura please? Can you do it, or something equivalent, in OpenSCAD...26 replies | 1232 view(s)
-
04-03-2021, 11:07 AMterrypin replied to a thread Cheap structured light scanner - anyone backed this ? in 3D Modeling, Design, ScannersFWIW, looks good to me too. Price seems to have increased significantly since your post. Basic unit = £361 and full 'combo' with turntable and...1 replies | 1446 view(s)
-
04-03-2021, 10:48 AMWhile trying to understand a mistake in a recent print I've just realised one likely cause. I'd been assuming that after changing parameters (such as...7 replies | 765 view(s)
-
04-02-2021, 12:16 PMThanks CA, but at the time of posting the Ender 3 V2 seemed to be printing OK. My worry was because I expected trouble because of there being so...2 replies | 251 view(s)
-
04-02-2021, 06:44 AMI started a discussion yesterday at https://www.thingiverse.com/thing:2938921/comments But can't realistically expect feedback to my latest...2 replies | 251 view(s)
-
03-31-2021, 09:57 AMterrypin started a thread Thingiverse downloads give security warnings in General 3D Printing DiscussionWhen working with files downloaded from thingiverse.com I'm frequently being pestered with Win 10 warning messages. This one below is typical. Do...0 replies | 161 view(s)
-
03-30-2021, 01:48 PMI’m wondering if by ‘decorations’ he meant ‘reinforcements’ or similar3 replies | 343 view(s)
-
03-29-2021, 01:18 PMThanks CA. I could find no text either. The ‘PCB’ does not seem part of the print. Presumably just to show its intended position. If I hear back...3 replies | 343 view(s)
-
03-29-2021, 11:33 AMI placed a comment in https://www.thingiverse.com/thing:1264391 so hope to hear from the author. But meanwhile can anyone make sense of the 'Vent'...3 replies | 343 view(s)
-
03-29-2021, 08:04 AMIs this the one you want?https://www.dropbox.com/s/fp6n92wxof32wqv/slic3r-mswin-x86-1-2-9a-stable.zip?raw=115 replies | 4822 view(s)
-
03-29-2021, 07:43 AMThanks both. Sounds easier than I’d expected. We’ll see...4 replies | 444 view(s)
About terrypin
Basic Information
Statistics
Total Posts
- Total Posts
- 62
- Posts Per Day
- 1.35
General Information
- Last Activity
- Yesterday 01:07 PM
- Join Date
- 03-05-2021
What plastic materials can I print?
04-14-2021, 09:59 AM in General 3D Printing Discussion