- Tab Content
- Bikeracer2020's Activity
- About Me
- Tab Content
-
Older Activity
-
Yesterday, 01:59 AMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpPossibilities...... Filament route to extruder not free enough. Filament trapped under other windings on reel. Teeth on extruder gunged up with...3 replies | 420 view(s)
-
04-22-2024, 03:57 PMBikeracer2020 replied to a thread Extruder not feeding during print, but purge works fine in Tips, Tricks and Tech HelpCheck nozzle temp in the slicer in case you have accidentaly changed to a lower setting. Happened to me recently.3 replies | 420 view(s)
-
04-22-2024, 03:49 PMBikeracer2020 replied to a thread Ender 3 S1 Mostly Metal Sprite Extruder Issue in 3D Printer Parts, Filament & MaterialsYou need a short piece of teflon or PTFE tube from the extruder into the hot end to support the filament.1 replies | 346 view(s)
-
04-16-2024, 12:32 PMBikeracer2020 replied to a thread Catastrophic failure on Creality Ender-3 V3 KE in Tips, Tricks and Tech HelpThe filament monster is probably because the nozzle has a less than perfect seal to the hot end, causing the molten filament to leak. I don't know...1 replies | 752 view(s)
-
04-14-2024, 01:46 AMDid You adjust the 'Z' offset in the slicer or just the 'Z' height when setting the initial nozzle difference? I should have made that clearer in...5 replies | 3452 view(s)
-
04-12-2024, 11:03 AMThe line is called a 'Z' seam, it happens where one layer ends and the next one starts. There are settings in the slicer as to where you want it...2 replies | 926 view(s)
-
04-12-2024, 02:21 AMTwo suggestions...... Try Prusaslicer or Orca slicer. Or email.. may@qd3dprinter.com2 replies | 1263 view(s)
-
04-12-2024, 02:13 AMBikeracer2020 replied to a thread AI generated 3d models - Revolutionary or Evolutionary??? in 3D Modeling, Design, ScannersI think all this AI generated stuff is rapidly leading to a place where it will be impossible to distinguish between fact and fiction. In your...2 replies | 1514 view(s)
-
04-11-2024, 06:08 AMBikeracer2020 replied to a thread WHY DOES MY PRINT LOOK LIKE THIS Please help! in General 3D Printing DiscussionTry just using your standard slicer profile for the filament.1 replies | 1110 view(s)
-
04-08-2024, 09:55 AMBikeracer2020 replied to a thread Printer thinks it's done but it isn't in Tips, Tricks and Tech HelpCheck the way the filament feeds off the reel for any sign that the filament is trapped under another winding causing the filament to stop feeding...9 replies | 2657 view(s)
-
04-02-2024, 09:43 AMBikeracer2020 replied to a thread Modded Creality CR10 print quality issues in Tips, Tricks and Tech HelpThat means your 'e' steps are right. In your slicer there should be a flow ratio setting or extrusion multiplier. In Orca slicer there is a flow...3 replies | 1840 view(s)
-
04-02-2024, 08:25 AMBikeracer2020 replied to a thread Modded Creality CR10 print quality issues in Tips, Tricks and Tech HelpPossibly under extrusion with the 0.6 nozzle3 replies | 1840 view(s)
-
03-31-2024, 01:37 PMBikeracer2020 replied to a thread Neptune 3 Pro, Prusa slicer won't stick on plate in General 3D Printing DiscussionDid you print a few squares to check the bed level? Can you go into your slicer settings and increase the 'Z' offset by either plus or minus 0.02...5 replies | 2297 view(s)
-
03-31-2024, 10:27 AMBikeracer2020 replied to a thread Neptune 3 Pro, Prusa slicer won't stick on plate in General 3D Printing DiscussionIt's the 'Z' offset that needs adjusting not the 'Z' height. Have a look on Youtube for videos on adjusting it. You can adjust the "z" offset...5 replies | 2297 view(s)
-
03-31-2024, 10:15 AMBikeracer2020 replied to a thread Neptune 3 Pro, Prusa slicer won't stick on plate in General 3D Printing DiscussionSuggestion........ Print perhaps 6-9 random 50mm x 50mm squares just 0.2mm thick on your bed. This should show you how level your bed is and...5 replies | 2297 view(s)
-
03-30-2024, 03:17 PMBikeracer2020 replied to a thread Printer thinks it's done but it isn't in Tips, Tricks and Tech HelpThe whole STL looks odd to me. Normally the STL would be just the actual wing I think, I can't see the point in printing the whole rectangle in...9 replies | 2657 view(s)
-
03-30-2024, 11:53 AMBikeracer2020 replied to a thread Printer thinks it's done but it isn't in Tips, Tricks and Tech HelpWhen I load your STL into Orca slicer it shows the first fifteen layers are just a solid rectangle, the remaining sixteen layers are just the walls...9 replies | 2657 view(s)
-
03-30-2024, 08:11 AMBikeracer2020 replied to a thread Printer thinks it's done but it isn't in Tips, Tricks and Tech HelpCan you post the file you are slicing?9 replies | 2657 view(s)
-
03-27-2024, 04:17 PMBikeracer2020 replied to a thread Which 3d printer for small compontents? in General 3D Printing DiscussionThere are several cad programs that you can use, some of which are free to use. Like anything new, there is a learning curve so have a look on...9 replies | 3722 view(s)
-
03-27-2024, 02:41 AMBikeracer2020 replied to a thread Ender 3 V2 (NEO) - Uneven first layers in Tips, Tricks and Tech HelpSuggestion........ Print some random one layer thick 50mm squares at 0.2mm layer height. Examine the result. Then increase or decrease the 'Z'...3 replies | 2406 view(s)
About Bikeracer2020
Basic Information
Statistics
Total Posts
- Total Posts
- 613
- Posts Per Day
- 0.42
General Information
- Join Date
- 05-07-2020
Extruder not feeding during print,...
Yesterday, 01:59 AM in Tips, Tricks and Tech Help