- Tab Content
- Bikeracer2020's Activity
- About Me
- Tab Content
-
Older Activity
-
03-27-2024, 04:17 PMBikeracer2020 replied to a thread Which 3d printer for small compontents? in General 3D Printing DiscussionThere are several cad programs that you can use, some of which are free to use. Like anything new, there is a learning curve so have a look on...9 replies | 1899 view(s)
-
03-27-2024, 02:41 AMBikeracer2020 replied to a thread Ender 3 V2 (NEO) - Uneven first layers in Tips, Tricks and Tech HelpSuggestion........ Print some random one layer thick 50mm squares at 0.2mm layer height. Examine the result. Then increase or decrease the 'Z'...3 replies | 1131 view(s)
-
03-22-2024, 10:47 AMBikeracer2020 replied to a thread Kywoo Tycoon 3D - Impossible to print after using PETG in Tips, Tricks and Tech HelpJust be aware that a hardened steel nozzle might cause problems for normal plastic filament, if it does, just fit a normal brass nozzle. I believe...7 replies | 4301 view(s)
-
03-21-2024, 03:34 AMBikeracer2020 replied to a thread Kywoo Tycoon 3D - Impossible to print after using PETG in Tips, Tricks and Tech HelpYou can cut a piece of new teflon tube, make sure the cut is at 90 degrees at the end and a snug fit against the nozzle. Ideally you need to...7 replies | 4301 view(s)
-
03-20-2024, 02:46 PMBikeracer2020 replied to a thread Kywoo Tycoon 3D - Impossible to print after using PETG in Tips, Tricks and Tech HelpDoes the extruder have a teflon tube between the exruder and the nozzle? If it does is there any sign of degradation? Also check that the end is...7 replies | 4301 view(s)
-
03-20-2024, 09:04 AMBikeracer2020 replied to a thread Kywoo Tycoon 3D - Impossible to print after using PETG in Tips, Tricks and Tech Helpjust suggestions..... Check extruder teeth are clean and not filled with filament. Do a cold pull to clear the nozzle of any old filament....7 replies | 4301 view(s)
-
03-19-2024, 12:14 PMBikeracer2020 replied to a thread Large gaps with 100% infill. Help! in General 3D Printing DiscussionJust my take on the problem...... Does the new hotend have a thermal break in it or does the teflon tube actually contact the nozzle? If the...2 replies | 3120 view(s)
-
03-18-2024, 03:07 PMBikeracer2020 replied to a thread Adventurer 3 filling holes in design! in Tips, Tricks and Tech HelpLoaded your STL into Orca slicer and it appears you have two STL's one on top of the other.1 replies | 2120 view(s)
-
03-12-2024, 11:49 AMMost FDM filament is not recycleable it seems, so chuck it in the trash bin.2 replies | 3456 view(s)
-
03-12-2024, 11:47 AMI've been using the same rough side PEI sheet for two years now and have just done the following..... Check bed level. Clean bed with IPA on a...1 replies | 2220 view(s)
-
03-10-2024, 01:29 AMBikeracer2020 replied to a thread which filament is most sun/heat/UV resistant in General 3D Printing DiscussionIf you have an enclosed printer ASA would be a good choice, or possibly ASA-X. Also because of the nozzle temp around 250 you really need an all...1 replies | 2727 view(s)
-
03-08-2024, 10:00 AMBikeracer2020 replied to a thread Ender 3 S1 Pro - Nozzle Collides with Infill on Taller Prints in Tips, Tricks and Tech HelpThere should be a setting in your slicer that tells the extruder not to travel over printed parts. That might help.2 replies | 3612 view(s)
-
03-03-2024, 02:14 AMBikeracer2020 replied to a thread creality ender 3 v2 not extruding filament properly in Tips, Tricks and Tech HelpCould be the nozzle is too close to the bed.....perhaps adjust the "z" offset in +0.02 increments. Print a bed leveling test to check. Clean...1 replies | 2392 view(s)
-
03-01-2024, 02:31 AMTry a search on YouTube for Bed levelling and First layer problems, loads of videos on the subject showing what the problems are and the solutions. ...1 replies | 2032 view(s)
-
02-28-2024, 11:25 AMI'm no expert by any means, but for what it's wortrh......Try ORCA slicer and use the X-CF pro profiile in it with a generic PLA profile and just...5 replies | 4224 view(s)
-
02-28-2024, 05:42 AMFrom the photos it looks like you are using the smooth side of the PEI bed sheet, if so, try the rough side and re level the bed or use some glue...5 replies | 4224 view(s)
-
02-28-2024, 05:19 AMPerhaps manually transfer the settings from your current slicer into ORCA slicer as a start. bit tedious, but one way to make your own slicer...6 replies | 4320 view(s)
-
02-28-2024, 02:49 AMWhich printer are you using?6 replies | 4320 view(s)
-
02-28-2024, 02:18 AMJust a suggestion......... Check your extruder 'e' steps and try ORCA slicer, it has some built in calibration files that you just have to print.6 replies | 4320 view(s)
About Bikeracer2020
Basic Information
Statistics
Total Posts
- Total Posts
- 595
- Posts Per Day
- 0.42
General Information
- Join Date
- 05-07-2020
Which 3d printer for small...
03-27-2024, 05:24 PM in General 3D Printing Discussion