- Tab Content
- Bikeracer2020's Activity
- About Me
- Tab Content
-
Older Activity
-
Yesterday, 03:07 PMBikeracer2020 replied to a thread Adventurer 3 filling holes in design! in Tips, Tricks and Tech HelpLoaded your STL into Orca slicer and it appears you have two STL's one on top of the other.1 replies | 194 view(s)
-
03-12-2024, 11:49 AMMost FDM filament is not recycleable it seems, so chuck it in the trash bin.2 replies | 2614 view(s)
-
03-12-2024, 11:47 AMI've been using the same rough side PEI sheet for two years now and have just done the following..... Check bed level. Clean bed with IPA on a...1 replies | 1566 view(s)
-
03-10-2024, 01:29 AMBikeracer2020 replied to a thread which filament is most sun/heat/UV resistant in General 3D Printing DiscussionIf you have an enclosed printer ASA would be a good choice, or possibly ASA-X. Also because of the nozzle temp around 250 you really need an all...1 replies | 2220 view(s)
-
03-08-2024, 10:00 AMBikeracer2020 replied to a thread Ender 3 S1 Pro - Nozzle Collides with Infill on Taller Prints in Tips, Tricks and Tech HelpThere should be a setting in your slicer that tells the extruder not to travel over printed parts. That might help.2 replies | 3171 view(s)
-
03-03-2024, 02:14 AMBikeracer2020 replied to a thread creality ender 3 v2 not extruding filament properly in Tips, Tricks and Tech HelpCould be the nozzle is too close to the bed.....perhaps adjust the "z" offset in +0.02 increments. Print a bed leveling test to check. Clean...1 replies | 2204 view(s)
-
03-01-2024, 02:31 AMTry a search on YouTube for Bed levelling and First layer problems, loads of videos on the subject showing what the problems are and the solutions. ...1 replies | 1877 view(s)
-
02-28-2024, 11:25 AMI'm no expert by any means, but for what it's wortrh......Try ORCA slicer and use the X-CF pro profiile in it with a generic PLA profile and just...5 replies | 3838 view(s)
-
02-28-2024, 05:42 AMFrom the photos it looks like you are using the smooth side of the PEI bed sheet, if so, try the rough side and re level the bed or use some glue...5 replies | 3838 view(s)
-
02-28-2024, 05:19 AMPerhaps manually transfer the settings from your current slicer into ORCA slicer as a start. bit tedious, but one way to make your own slicer...6 replies | 3893 view(s)
-
02-28-2024, 02:49 AMWhich printer are you using?6 replies | 3893 view(s)
-
02-28-2024, 02:18 AMJust a suggestion......... Check your extruder 'e' steps and try ORCA slicer, it has some built in calibration files that you just have to print.6 replies | 3893 view(s)
-
02-27-2024, 09:03 AMIf your filament is ground in half, check the fteeth on the extruder are not clogged up needing to much pressure on the filament. Check for a...1 replies | 1418 view(s)
-
02-25-2024, 01:23 PMLoads of info on YouTube. Teaching Tech Makers Muse CNC Kitchen Thomas Sanlandera 3D Printing Nerd and many more. Just search 3D printing.2 replies | 3000 view(s)
About Bikeracer2020
Basic Information
Statistics
Total Posts
- Total Posts
- 586
- Posts Per Day
- 0.41
General Information
- Join Date
- 05-07-2020
Newbie Question
Yesterday, 12:02 AM in Tips, Tricks and Tech Help